Craftsman 3000 MAX PSI Serie Guia De Inicio Rapido

WARNING Failure to read and follow the operator's
manual and all operating instructions can
result in death, bodily injury, and/or property
damage.
WARNING Fuel and its vapors are flammable and
explosive. Turn off engine and wait at least
2 minutes before refueling. Let spilled fuel
evaporate before starting engine. Always allow
space for fuel expansion.
WARNING High pressure water spray can cut
through skin. Never spray people or animals,
as injury can result. Spray gun traps high
water pressure, even when engine is stopped
and water is disconnected. ALWAYS point spray gun in
safe direction, press red button and squeeze spray gun
trigger, to release high pressure, every time you stop
engine.
You will need:
• Utility knife • Unleaded fuel • Garden hose, 50 feet or less
• Oil Funnel (optional)
Unpack pressure washer
1. Remove everything from carton except pressure washer.
2. Open carton completely by cutting each corner from top to bottom.
3. Ensure you have all included items prior to assembly.
If items are damaged or missing, call 1-800-222-3136.
Assemble pressure washer
1. Place handle (a) onto handle supports connected to main unit. Make
sure holes in handle align with holes on handle supports.
2. Insert two handle bolts (g) through holes from inside of unit and
attach with plastic knobs (f) from outside of unit. Tighten by hand.
3. By loosening both knobs to the middle section of the attachment bolt,
the upper handle can fold forward to store flat atop the cold engine.
NOTICE DO NOT fold the handle down while the engine is hot.
4. Place accessory tray (e) over four holes on back side of handle. Push
all four tree clips (b) into holes until they sit flat against accessory
tray.
3
5. Attach rope guide (h) to handle with plastic knob (d). Tighten by
hand. Route starter rope through guide.
4
6. Align hose wrap (j) to the back side of accessory tray. Locate notch
with "unlock" icon (A) on hose wrap. Position notch at top with hose
wrap in vertical position. Clips in the back of accessory tray should
slide into the grooves on the inside surface of hose wrap. Slide hose
wrap on back of accessory tray and rotate 1/8 turn until "locked"
icon (B) is in vertical position.
5
7. Attach two bottle brackets (p) to handle with carriage bolts (c) and
plastic knobs (d). Tighten by hand.
6
2-IN-1 Soap System
1. The pressure washer is equipped with two detergent siphoning
hoses.
Project Pro ® PerfectMix™ Siphon: Blue tube with blue bottle cap:
When using the blue PerfectMix™ siphon (m), use the PerfectMix™
Extreme Concentrate straight from the bottle.
Standard Siphon Tube: Clear tube with filter: When using the clear
standard siphon tube (A), dilute 1 part PerfectMix™ Extreme
Concentrate to 16 parts water (4 oz of concentrate makes 1/2 gallon
of mix).
7
Attach Project Pro ® PerfectMix™
Siphon to Pump and Concentrate Bottle
1. Place PerfectMix™ bottle (B) (not included) in the wire-form bracket
on the handle. Remove cap from bottle and insert the PerfectMix™
Siphon (m). Screw the siphon unit to the top of the bottle (B). Use
the clip on the cap (C) to snap siphon to wire form bracket when
siphon is not in a concentrate bottle.
7
® PerfectMix™ Siphon
2. Attach the hose end of the blue Project Pro
(m) to the barbed hose fitting (D) on the pump.
© 2010 Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.
*This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101 (Testing and Rating Performance of Pressure Washers).
Quick Start Guide
3000 MAX PSI* Pressure Washer
WARNING Outdoor use ONLY. DO NOT start or run
engine indoors or in an enclosed area, even
if windows and doors are open. Running
engines give off carbon monoxide, an
odorless, poison gas that can cause nausea, fainting or
death.
WARNING Starter cord kickback (rapid retraction)
can result in bodily injury. NEVER pull
starter cord without first relieving spray
gun pressure. Pull starter cord slowly until
resistance is felt, then pull rapidly. Kickback will pull
hand and arm toward engine faster than you can let go.
High pressure can cause spray gun to kickback. Hold
spray gun with both hands during use.
WARNING Risk of eye injury. Spray can splash
back or propel objects. Always wear indirect
vented (chemical splash) safety goggles,
marked to comply with ANSI Z87.1 when
using or in vicinity of this equipment. NEVER substitute
safety glasses or dry-condition goggles for indirect
vented safety goggles.
Items Included:
Operator's Manual (not shown)
• Safety goggles (indirect vented type)
1
a
2
1
2
f
3
b
e
4
h
5
A
7
j
6
c
p
7
m
8
B
Add Engine Oil and Fuel
NOTICE You MUST properly fill engine with oil before attempting to
start pressure washer.
NOTICE DO NOT use E85 fuel.
NOTICE DO NOT mix oil with fuel.
1. Move pressure washer outdoors to a flat, level surface.
2. Clean area around oil fill and remove yellow oil fill cap/dipstick (E).
3. Using oil funnel (optional), slowly pour entire contents of oil bottle
(n) into oil fill.
4. Replace and fully tighten oil fill cap.
5. Clean area around fuel fill cap and remove fuel cap (F).
6. Slowly add regular unleaded fuel to fuel tank. Be careful not to
overfill. To allow for fuel expansion, do not fill above the bottom of
the fuel tank neck.
7. Replace fuel cap. Let any spilled fuel evaporate before starting
engine.
Move Pressure Washer
to Safe Operating Location
WARNING Outdoor use ONLY. DO NOT start or run engine indoors
or in an enclosed area, even if windows and doors are open.
Running engines give off carbon monoxide, an odorless,
poison gas that can cause nausea, fainting or death.
1. Move pressure washer outdoors to a flat, level surface. Running
engines give off carbon monoxide.
2. Keep at least 5 ft. (1.5 m) clearance on all sides of pressure washer
including overhead to reduce the risk of exhaust heat or exhaust
gases igniting nearby combustible material.
Connect Spray Gun
NOTICE Remove and discard 2 shipping caps from high pressure outlet
and garden hose inlet connections.
1. Uncoil high pressure hose (q) and attach one end of hose to base of
spray gun (r). Tighten by hand.
2. Attach other end of high pressure hose (q) to high pressure outlet
(G) on pump. Tighten by hand.
Connect Water Supply
NOTICE If inlet screen is damaged or missing, DO NOT use pressure
washer, call 1-800-222-3136.
1. Inspect garden hose inlet screen for damage.
2. Clean screen if it contains debris or have it replaced if damaged. DO
NOT run pressure washer if inlet screen is damaged or missing.
3. Run cold water through garden hose for 30 seconds to clean out any
debris. Connect garden hose (J) (not to exceed 50 feet in length) to
water inlet (H). Tighten by hand.
Start Pressure Washer
NOTICE You MUST connect and turn on water supply fully before
starting engine.
1. Put on safety goggles.
WARNING Risk of eye injury. Spray can splash back or propel
objects. Always wear indirect vented (chemical splash)
safety goggles, marked to comply with ANSI Z87.1 when
using or in vicinity of this equipment. NEVER substitute
safety glasses or dry-condition goggles for indirect vented safety
g
goggles.
2. Turn on water supply.
3. Press red safety button (K) on spray gun and pull trigger until water
comes out in a steady stream.
4. Attach nozzle extension (s) to spray gun (r).
5. Pull back on collar of nozzle extension (s), insert selector nozzle (k)
and release collar. Tug on selector nozzle to make sure it is securely
in place. For 5 in1 Selector Nozzle instructions, see operator's
manual.
16
6. Push engine On/Off switch (L) to "I or On" position.
NOTICE This unit is equipped with a ReadyStart ® engine. A
ReadyStart ® engine means there is no priming or choking required.
WARNING Starter cord kickback (rapid retraction) can result in
bodily injury. NEVER pull starter cord without first relieving
d
spray gun pressure. Pull starter cord slowly until resistance
is felt, then pull rapidly. Kickback will pull hand and arm
toward engine faster than you can let go. High pressure can cause
spray gun to kickback. Hold spray gun with both hands during use.
B
7. When starting engine, position yourself as recommended and
grasp starter grip handle and pull slowly until you feel some
resistance. Then pull rapidly to start engine. After each starting
attempt, where engine fails to run, always point gun in safe direction
press red safety button and squeeze spray gun trigger to release
high pressure.
18
8. Return recoil starter slowly. DO NOT let rope "snap back" against
starter.
9. Point gun toward surface to be cleaned. Press red button and pull
trigger to begin spraying.
d Stop Pressure Washer
1. Release spray gun trigger and let engine idle for two minutes.
2. Push engine On/Off switch (L) to "O or Off" position.
A
3. Turn off water supply. Point spray gun in safe direction, red safety
button and squeeze spray gun trigger to relieve retained high water
pressure.
4. For long term storage instructions, see operator's manual.
C
5. Remove safety goggles.
Have Questions?
Do not return to store. We can help.
Call Customer Service Toll-Free 1-800-222-3136
Or visit our website www.craftsman.com
8
9
9
E
9
10
Exhaust Port
Pointed away from
dwelling openings
11
10
r
12
11
12
13
13
14
13
15
16
17
14
15
17
18
17
D
m
F
q
q
G
Inlet Screen
H
J
K
r
s
s
k
L