Idiomas disponibles
Idiomas disponibles
English
Wall Mounting
Some PORTER-CABLE chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Installing a Bit or Accessory into a Keyless
Single Sleeve Chuck (Fig. A)
WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
switch and disconnect tool from power source when
changing acces sories.
WARNING: Always ensure the bit is secure before
starting the tool. A loose bit may eject from tool
causing possible personal injury.
Your tool features a keyless chuck
sleeve
6
for one-handed operation of the chuck.
To insert a drill bit or other accessory, follow these steps.
1. Turn tool off and remove battery pack.
2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
3. Insert the accessory about 3/4" (19 mm) into the
chuck
5
and tighten securely by grasping and rotating
the chuck sleeve
6
clockwise with one hand while
holding the tool with the other. When the chuck is nearly
tightened you will hear a clicking sound. After 3-6 clicks
the chuck is securely tightened around the accessory.
Your tool is equipped with an automatic spindle lock
mechanism. This allows you to open and close the chuck
with one hand.
4. Be sure to tighten chuck with one hand on the
chuck sleeve and one hand holding the tool for
maximum tightness.
5. To release the accessory, repeat steps 1 and 2 above.
8
5
with one rotating
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. D)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
release button
10
and firmly pull the battery pack out of
the tool handle. Insert it into the charger as described in
the charger section of this manual.
Proper Hand Position (Fig. E)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the top of the
drill
as shown, with the other hand on the main handle
8
Variable Speed Paddle Switch (Fig. A)
1. To turn the tool on, squeeze the
variable speed paddle switch
2. To turn the tool off, release the variable speed paddle
switch. Your tool is equipped with a brake.
nOTE: The chuck will stop as soon as the variable speed
paddle switch is fully released.
3. The variable speed switch enables you to select the best
speed for a particular application.
4. The more you squeeze the paddle, the faster the tool
will operate.
5. Use lower speeds for starting holes without a
centerpunch, drilling in metals or plastics, driving screws
and drilling ceramics.
6. Higher speeds are better for drilling in wood,
wood compositions and for using abrasive and
polishing accessories.
7. For maximum tool life, use variable speed only for
starting holes or fasteners.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
9
into the tool handle, align
1
.
.
7
