TMEZON MZ-AHD-V715T Manual De Instrucciones página 6

Unlock way: Card unlock.
Unlock time: 2s safety closed mode
Note: Reset factory will not delete user's information.
Disable anti-dismantling detection function:
Long press and unrelease the call button, then power on the device, anti-dismantling
function disable after heard "DiDi DiDi" 4 rings.
Doorbell operation instruction
Enter into administrator operation status: Press * + admin password (default admin password
999999) +#, the device flash slowly, it means that the device enter setup mode. (the speed of flash
slow is 1 time/s and flash fast is 2 times/s)
*
#
Note: for return, for confirm
Below setup must be accomplished under setup mode.
(0) Modify admin password, public unlock password and restore factory setting.
Modify admin password: Press 0 (button light flash fast) + 77 + # + NNNNNN (six digits
password) + # + NNNNNN (Input password again ) + #
Modify public password: Press 0 (press button light flash fast) + 11 + # + NNNNNN (six
digits password) + # + NNNNNN (Input password again ) + #.
Factory reset setup: Press 0 (button light flash fast) + 99 + # (After Di..., button light
flash slow), device factory reset successfully.
Note: After factory reset, only the device's password and unlock password will be deleted,
ID cards are still valid.
(1) Add card
Press 1 (button light flash fast) + 000 - 199 + # + read the card (After Di..., add a card
successfully).
It will have a default password "0000" when adding user card, but this password is
unable to unlock, only for user to modify password
(2) Delete user
Delete missing card: Press 2 (button light flash fast) + NNN + # (NNN means the
position of the card that you want to delete. The scope of NNN is from 000-199) .It
means delete the card and password successfully when buzzer ring 3 times ( Di..Di..Di..)
Delete read card: Press 2 (button light flash fast) + read a card, Di..Di..., Di....Di...,
then the card and related password deleted.
Delete all: Press 2 (button light flash fast) + 88 + # (Di...Di..Di..button light flash slow),
delete all successfully.
.
GB-9
(3) Setup unlock mode
A. Press 3 (button light flash fast) + 00 + # ( Di..Di.., button light flash slow) --- The
card unlock only.
B. Press 3 (button light flash fast) + 01 + # ( Di..Di.., button light flash slow) --- The
card or password unlock.
C. Press 3 ( button light flash fast) + 02 + # ( Di..Di... button light flash slow) --- The card
and password unlock.
(4) Modify the unlock time of relay
Press 4 ( button light flash fast) + 00 - 99 +# ( Di..Di.., button light flash slow) The 00-99
means unlock time. Take a example if set as 02, the unlock time is 2s, and so on.
(5) Safety mode setup
Press 5 (button light flash fast) + 00 + # ( Di..Di.., button light flash slow) --- Off mode.
Press 5 (button light flash fast) + 01 + # ( Di..Di.., button light flash slow) --- Locked mode.
(Means within 5 minutes, continue use wrong card or incorrect password for 10 times, the
device will be locked out for 2 minutes, button light fast flashing, indoor monitor start
monitoring automatically. Then card and password won't work in this 2 minutes.
Press 5 (button light flash fast) + 02 + # ( Di..Di.., button light flash slow) --- Alarm mode
(Means within 5 minutes, continue to use wrong card or incorrect password for 10 times,
the built in buzzer will alarm for 1 minute, button light fast flashing, indoor monitor start
monitoring automatically).
Note: In the process of setup, press * can exit or back to last step.
User operation
User modify password by card：
Press *, read card + old password ( default 0000, slow flashing)+ # +NNNN (4 digits as
new password) + # +NNNN (Input password again), if no mistake on operation, then the
buzzer will ring as Di....., button light stop flashing, means password modified successfully.
Card access to unlock
The valid card which added in the detecting area, unlock the door.
ID card or password unlock
Swipe the added valid card or input password + #, one of them is correct to open the
door.
ID card and password to unlock
Swipe the valid card and input related password + #, both correct can unlock the door.
Note: After setup successfully each time, press * to exit Setup mode
GB-10