Operation; Switching Off; Practical Tips - EINHELL AGILLO Manual De Instrucciones

equipment (Fig. 2/Item 1). The battery will be
heard to click into place when it has been pushed
fully in (Fig. 1). To take out the battery, press the
pushlock button (Fig. 15/Item K) and remove the
battery.
5.11 Charging the battery (Fig. 14)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(D) into the socket outlet. The green LED will
then begin to fl ash.
3. Insert the battery pack (E) into the charger
(D).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long
service, you should take care to recharge it
promptly. You must recharge the battery pack
when you notice that the power of the cordless
grass trimmer drops. Never allow the battery pack
to become fully discharged. This will cause it to
develop a defect.
5.12 Battery capacity indicator (Fig. 15)
Press the button for the battery capacity indicator
(Item H). The battery capacity indicator (Item F)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
Anl_SA_Agillo_SPK8.indb 37 Anl_SA_Agillo_SPK8.indb 37
GB
All LEDs fl ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.

6. Operation

Please note that the statutory regulations gover-
ning noise abatement may diff er from one loca-
tion to another.
Danger! The guard hood must be fi tted when car-
rying out work.
6.1 Switching the equipment on and off , ad-
justing the speed (Fig. 16)
Switching on and setting the speed
Press the safety lock-off (3) and press the On/Off
switch (2) at the same time. Adjust the speed du-
ring operation by pressing the On/Off switch to a
greater or lesser extent. The harder you push, the
higher the speed.
Switching off
Release the On/Off switch.

6.2 Practical tips

Practice all the work steps with the motor swit-
ched off and without the rechargeable battery be-
fore you start to use the equipment. Only use the
cutting line to mow grass that is dry. If the grass
is long, the grass must be cut shorter in stages
(Fig. 17).
Extending the cutting line (Fig. 18)
Danger! Do not use any kind of metal wire or me-
tal wire encased in plastic in the line spool. This
may cause serious injuries to the user.
The grass trimmer has a semi-automatic line
extension system (automatic jog line feed). Each
time you activate the semi-automatic line exten-
sion system, the line is automatically extended to
ensure that you can cut your lawn with the perfect
cutting width at all times. To extend the cutting
line, run the motor and tap the line spool on the
ground. This will automatically extend the line.
The blade on the guard hood will cut the line to
the permissible length. Please note that the more
often you activate the semi-automatic line exten-
sion system, the more the line will wear.
- 37 -
11.06.2019 10:34:22 11.06.2019 10:34:22