Important Remarks - JBM 53688 Manual De Instrucciones

EN
INSTRUCTION MANUAL
IMPORTANT INFORMATION! You must charge completely before first use, after every jump start
and every 30 days
PRODUCT'S PRESENTATION
The jump starter is designed to start cars, boats and
other vehicles when the vehicle's battery cannot be
used, avoiding you the need to seek assistance from
other drivers. It is equipped with 12/24V power source,
a LED light which can be used in emergency situations,
and LED lights that indicates the battery's internal sta-
tus. This jump starter can be used to provide power to
12V DC appliances by means of its 12V DC outlet socket
and can be charged with an external charger by con-
necting it to the charging socket. It also has an auto-
matic current overload protection for the battery.
SAFETY INSTRUCTRIONS
WARNING! Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions
listed below may result in electric shock, fire and/or
serious injury.
• Keep the working area clean and well lit.
• Keep children and non-authorized personnel away
from the working area.
• Do not operate the angle grinder if you get tired
easily or under the influence of drugs, alcohol or
medication.
• Dress properly. Do not wear loose clothing or
jewelry and contain long hair.
• Always wear eye and respiratory protection.
• Do not operate the tool in the presence of flam-
mable liquid or gases.
• Do not expose the unit to rain or wet conditions.
• Make sure the switch (black rotatory knob) is in the
off position while not in use. It will prevent any da-
maged caused by an accidental connection be-
tween red and black clamps.
• Do not connect red and black clamps directly or to
the same conductor at the same time.
• Before use, make sure the car battery and jump
starter selected voltage matches, and clamps are
connected to the correct polarities.
NOTE! Do not use the jump starter as a car battery re-
placement and the vehicle power supply.
• Do not pull or carry the unit by its cables, and do
not pull the clamps from the battery terminals.
• Do not store the tool in wet locations or places
where temperature may exceed 50 C.
• Have water and soap nearby in case battery acid
comes in contact with skin, clothing or eyes, and
wash immediately if so.

IMPORTANT REMARKS

1. The warning light (7) changes the color in different
speed as a warning for the operator:
• If the clamps are correctly connected to the ba-
ttery terminals, the light is green.
• If the clamps are connected to the battery ter-
minals incorrectly, the light will flicker in red two
times per second, and an alarm will sound.
• If the clamps are connected to a car with 24V
system and the voltage switch is in 12V position,
the light will flicker in red two times per second,
and an alarm will sound.
2. If the internal battery voltage is low, the charging
status light (3) will flicker in red.
3. The 12/24V switch (12) must be in 12V position when
recharging the jump starter. If the user turns the
switch to the "OFF" or "24V" position, the charging
status lights 3 and 4 will flicker in red and green,
and an alarm will sound.
OPERATION
Charging the jump starter
NOTE! Check the internal power status by pressing the
power testing button (9) and checking the voltage me-
ter (8) before the first use. If the red charging status light
is on, charge the unit as soon as possible.
1. Connect the charger to the power supply.
2. Connect the charger plug into the charging soc-
ket (11).
3. The LED light (3) will turn on once the jump starter
is being charged.
4. Once the jump starter is fully charged, the LED li-
ght (4) will be on.
5. Remove the charger from the socket and discon-
nect the charger from the power supply.
12V DC output socket
You can use the jump starter to charge 12V DC applian-
· 4 ·
REF. 53688