Parallel Mode; Stereo Mode - FONESTAR SA-606 Manual De Usuario

CONNECTION
- Connect the loudspeakers to the required loudspeaker output depending on your installation. Do not use
more than one type of output at the same time.
- The loudspeakers must be connected in a series/parallel circuit so that the load impedance of the
loudspeakers is the same as the load impedance of the amplifier output and that the power supplied by
the amplifier does not exceed that withstood by the loudspeakers.
CH B
GND LIFT
- Once the connections have been made according to your needs, connect the devices to the power
supply and switch them on. After use, do not forget to switch off and disconnect the device from the
INPUTS
power supply.
Three operating modes can be selected using the selector located on the rear part of the device: parallel
mode (PAR), stereo mode (STE) or bridge mode (BRI).

PARALLEL MODE

Place the selector located on the rear part of the power amplifier in the PAR position.
In this mode, the input of the two channels will be the channel A input signal. Connect the CH A input and
the two loudspeaker outputs. The volume is adjusted separately.
CH B
GND LIFT
INPUTS
POWER

STEREO MODE

Place the selector located on the rear part of the power amplifier in the STE position.
In this mode, the two channels operate independently. Connect the two loudspeaker inputs and two outputs.
The channel volume is adjusted separately.
CH B
GND LIFT
INPUTS
CH B
GND LIFT
INPUTS
MIN
1
STE BRI
PAR
CH B
(1+, 1-)
-
MODE
STE BRI
CH A
PAR
400 W + 400 W RMS@4
300 W + 300 W RMS@8
STE BRI
PAR
CH B
(1+, 1-)
-
MODE
STE BRI
CH A
PAR
400 W + 400 W RMS@4
300 W + 300 W RMS@8
CLIP
MIN
STE BRI
1
PAR
CH B
(1+, 1-)
-
MODE
STE BRI
CH A
PAR
STE BRI
PAR
CH B
(1+, 1-)
-
MODE
STE BRI
CH A
PAR
400 W + 400 W RMS@4
300 W + 300 W RMS@8
POWER
MAX MIN MAX
CH A CH B
3 1
CH A
(1+, 1-)
STEREO/
PARALLEL
BRIDGE
8 ONLY
+ + -
(1+, 2-)
BRIDGE - 8 ONLY
OUTPUTS
CH A
(1+, 1-)
STEREO/
SA-606
PARALLEL
BRIDGE
8 ONLY
+ + -
(1+, 2-)
BRIDGE - 8 ONLY
OUTPUTS
2
CLIP
PROTECT
POWER
MAX MIN MAX
CH A CH B
3 1
CH A
(1+, 1-)
STEREO/
SA-606
PARALLEL
BRIDGE
8 ONLY
+ + -
(1+, 2-)
BRIDGE - 8 ONLY
OUTPUTS
CH A
(1+, 1-)
STEREO/ SA-606
PARALLEL
BRIDGE
8 ONLY
+ + -
(1+, 2-)
600 W RMS@8 BRIDGE - 8 ONLY
OUTPUTS
- 3 -
POWER AMPLIFIER SA-606
~115 V AC, 50/60 Hz FUSE: 16 A
~230 V AC. 50/60 Hz FUSE: 8 A
SA-606
STEREO POWER AMPLIFIER
400 + 400 W RMS, 4
300 + 300 W RMS, 8
600 W RMS BRIDGE 8
AC SELECT
POWER CONSUMPTION: 1,500 W
~115 V AC, 50/60 Hz FUSE: 16 A
~230 V AC. 50/60 Hz FUSE: 8 A
STEREO POWER AMPLIFIER
400 + 400 W RMS, 4
300 + 300 W RMS, 8
600 W RMS BRIDGE 8
AC SELECT
POWER CONSUMPTION: 1,500 W
POWER AMPLIFIER SA-606
~115 V AC, 50/60 Hz FUSE: 16 A ~230 V AC. 50/60 Hz FUSE: 8 A
STEREO POWER AMPLIFIER
400 + 400 W RMS, 4
300 + 300 W RMS, 8
600 W RMS BRIDGE 8
AC SELECT
POWER CONSUMPTION: 1,500 W
~115 V AC, 50/60 Hz FUSE: 16 A
~230 V AC. 50/60 Hz FUSE: 8 A
STEREO POWER AMPLIFIER
400 + 400 W RMS, 4
300 + 300 W RMS, 8
600 W RMS BRIDGE 8
AC SELECT
POWER CONSUMPTION: 1,500 W
EN