Tabla de contenido
Idiomas disponibles
Idiomas disponibles
TFA_No_35.1079_Anleitung_08_22
Wireless weather station
• During night-time, the atmospheric disturbances are usually less severe
and reception is possible in most cases. A single daily reception is ade-
quate to keep the accuracy deviation under 1 second.
• The clock automatically scans the time signal at 2.00 a.m., 8.00 a.m.,
2.00 p.m. and 8 p.m. every day to maintain accurate timing. If the recep-
tion is not successful, the DCF reception symbol disappears, but the DCF
time reception will be repeated again. The manually set time will be over-
written by the DCF time when the signal is received successfully.
6.3 Additional transmitters
• The wireless weather station can receive up to 3 temperature sensors. If
you have purchased additional transmitters, repeat step 1) for all extra
sensors. However, ensure that you leave 10 seconds in between the
reception of the last sensor and the set-up of the following sensor. The
wireless weather station will number the sensors in the order of set-up
automatically.
7. How to operate
• The base station has three sections on the LCD: Time Mode, Indoor Tem-
perature & Humidity Mode and Outdoor temperature mode. Press
SET/MODE button to change between the sections (arrow).
• Press the +/CH button in time mode to select the display of time, calendar
(day-month-year) and alarm time.
• In outdoor temperature mode press +/CH button to toggle between the
outdoor sensor 1,2,3 (If more than 1 sensor is used)
• During operation, all successful settings will be confirmed by an acousti-
cal signal.
• The instrument will quit the setting mode, if there is no button used with-
in 30 seconds.
7.1 Setting Mode
• Press the SET/MODE button for 3 seconds while in normal mode to enter
the normal setting mode.
• In the setting modes, press +/CH button or -/MAX/MIN button to select
the units or scroll the value. Holding the buttons will increase/decrease
digits in great steps.
• Press the SET/MODE button to select the following setting in sequence:
1. Time Zone Setting +-12 hrs.: The time zone is used for countries
where the DCF signal can be received but the time zone is different
from the German time (e.g. + 1=one hour later).
2. 12/24 hour format
3. Manual time setting (hours/minutes)
4. Calendar setting(year /month/ day)
5. Temperature display unit degree Celsius or Fahrenheit
6. Pressure threshold setting (default 3hPa, see 7.4)
16
06.09.2022
8:24 Uhr
Seite 9
Wireless weather station
7.2 Alarm clock function
• Press twice +/CH button in normal mode. Alarm Time ("AL") appears on
the LCD.
• When
viewing
the
Alarm
Time,
3 seconds to enter Alarm Time setting. Press +/CH button or
-/MAX/MIN button to adjust the alarm time. Confirm hours with
SET/MODE button and switch to minutes setting. Confirm with SET/MODE
button.
• Press -/MAX/MIN button to switch alarm on or off. If it is on,
shown on the LCD.
• Press +/CH button to return to time mode.
• On the display appear the current time and the alarm symbol.
• Press any button to stop the alarm (120 sec).
• If the alarm is not stopped, the increasing alarm will automatically turn
off after 2 minutes and will be reactivated at the same time.
7.3 Min/Max Mode
7.3.1 Indoor Temperture & Humidity
• Press the SET/MODE button to make the arrow point to INDOOR TEM-
PERATURE & HUMIDITY display section
• Press the -/MAX/MIN button to display the following values:
• Indoor temperature maximum
• Indoor temperature minimum
• Indoor humidity maximum
• Indoor humidity minimum
• Press the -/MAX/MIN button for 3 seconds, the above individual mini-
mum or maximum record will be reset to zero.
7.3.2 Outdoor Temperature Mode
• Press the SET/MODE button to make the arrow point to OUTDOOR TEM-
PERATURE display section.
• Press and release +/CH button to toggle between the outdoor sensor
1,2,3 (If more than 1 sensor is used)
• Press the -/MAX/MIN button to display the following values:
• Current channel outdoor temperature maximum
• Current channel outdoor temperature minimum
• Press the -/MAX/MIN button for 3 seconds, the above individual mini-
mum or maximum record will be reset to zero.
7.4 Weather forecast
sunny
partly
cloudy
• The four weather icons (sunny, partly cloudy, cloudy and rainy) represent
the weather forecast.
hold
SET/MODE
button
for
is
cloudy
rainy
17
Tabla de contenido
