Configuration - Aritech ACL580 Serie Instalación

To:
ACL870FL-
From
PB
ACL580xx POWER GND
GND
ACL580xx POWER +12V
+12V
Ext. PSU GND GND
Ext. PSU +12V +12V
NO1 &
Ext. PSU GND
COM2
Ext. PSU +12 V
Door Strike COM1
Door Magnet NC2
Installation
Mounting
See Figures 1, 2, and 3.
To install the keypad, follow the steps in the figure.
Wiring
See "Keypad wiring" on page 3.
Pairing keypad with ACL870FL-PB or ACL870SU-PB
1. Close the jumper (ACL870FL-PB) or set DIP switch to On
(ACL870SU-PB). The unit beeps continuously, and the red
LED blinks.
2. Open the Jumper / DIP switch
3. Wait for beep and OK beep (short, short, long beep). After
the OK beep, the keypad and ACL870FL-PB / ACL870SU-
PB are paired.

Configuration

Reset master code
Caution: Resetting the master code will delete all user codes.
Resetting the master code will also unpair ACL870FL-PB and
ACL870SU-PB.
See figure 5.
1. Disconnect power and close the jumper (Figure 5, step 1).
2. Reconnect power.
The keypad beeps continuously.
3. Open the Jumper (step 2).
Orange LED switches on, long beep sounds.
4. Press 000.
5. Enter the new master code (1 to 8 digits).
6. Press A to confirm.
4 / 16
ACL870SU-PB Door
Magnet /
Door
Strike
GND (black,
item 1)
+12V out
(brown, item 7)
GND (black,
item 1)
+12V (red,
item 2)
COM (yellow,
item 5)
+12V
NO (white,
item 6)
GND
7. Press B to exit.
Orange LED switches off.
Programming mode
To change keypad options, follow the steps below.
1. Authorize using the master code, or 000 when using the
keypad for the first time.
2. Validate the code by pressing B.
If you are not authorized to enter the programing mode,
the keypad transmits multiple short beeps, and the yellow
LED blinks rapidly.
If the code is valid, the programming mode is signalled
by 1 short and 1 long beeps, and indicated by the yellow
LED on. You can continue with the programming.
3. Enter the option number you want to change. Refer to
"Programming options" below.
4. Press A to validate the change.
If the change is invalid, the keypad transmits multiple short
beeps, and the yellow LED blinks rapidly. Return to step 3.
If the change is valid, it is confirmed by 2 short beeps.
Return to step 3.
To exit the programming mode, press B in any stage of the
programming mode. The yellow LED switches off.
Programming options
When in the programming mode, press a number to program
one of the following options.
Option Description
0 Add/change user or master code
To change master code, enter user number 000 followed by
the new master code (1 to 8 digits).
To add or change existing user, enter the user number (001
to 999), and a new user code (1 to 8 digits)
The new user is assigned to Relay 1
1 Set Relay 1 timer
To set toggle relay mode, press 00.
To set time in seconds, press 01 to 99.
The default time is 03 seconds.
2 Set Relay 2 timer
To set toggle relay mode, press 00.
To set time in seconds, press 01 to 99.
The default time is 03 seconds.
3 Assign output to the user
Enter the user number (001 to 999). Next, press 1 for Relay
1, and/or 2 for Relay 2.
4 Not used
5 Slave device
Press 2 to set ACL870FL-PB or ACL870SU-PB as a slave
device.
6 Buzzer, backlight, read range
Press 0 to set buzzer off, or 1 to on. Press 2 to for backlight
off, or 3 to on. Press 4 for backlight on key press, or 5 for
dimmed backlight.
The default values are the following: buzzer on, dimmed
backlight.
P/N 466-5607-ML • REV A • ISS 30JUL21