Bosch GOF 2000 CE Professional Manual Original página 24

All manuals and user guides at all-guides.com
OBJ_BUCH-622-001.book Page 24 Tuesday, January 15, 2008 5:10 PM
24 | English
Material Router bit di-
ameter (mm)
Hardwood (Beech)
Softwood (Pine)
Particle Board
Plastics
Aluminium
After longer periods of working at low speed, al-
low the machine to cool down by running it for
approx. 3 minutes at maximum speed with no
load.
Switching On and Off
Adjust the depth-of-cut before switching on or
off; see Section "Adjusting the Depth-of-cut".
To start the machine, press the On/Off switch
19 and keep it depressed.
To lock the pressed On/Off switch 19, press the
lock-on button 18.
To switch off the machine, release the On/Off
switch 19 or when it is locked with the lock-on
button 18, briefly press the On/Off switch 19
and then release it.
Constant Electronic Control
Constant electronic control holds the speed
constant at no-load and under load, and ensures
uniform working performance.
2 610 956 206 | (15.1.08)
Adjusting the Depth-of-cut
Thumb-
wheel 17
The adjustment of the depth-of-cut may on-
4 – 10 5 – 6 ly be carried out when the router is
12 – 20 3 – 4 switched off.
22 – 40 1 – 2
For coarse adjustment of the depth-of-cut, pro-
4 – 10 5 – 6
ceed as follows:
12 – 20 3 – 6
– Place the machine with the router bit mount-
22 – 40 1 – 3
ed on the workpiece to be machined.
– Set the scale for fine adjustment 2 to "0".
4 – 10 3 – 6
12 – 20 2 – 4
– Set the step buffer 8 to the lowest position;
22 – 40 1 – 3
the step buffer engages noticeably.
– Loosen the clamping lever for depth-of-cut
4 – 15 2 – 3
coarse adjustment 5 by turning in counter-
16 – 40 1 – 2
clockwise direction so that the depth stop 4
4 – 15 1 – 2
can move freely and faces against the step
16 – 40
1
buffer 8.
– Push the release lever 16 downward and
slowly lower the plunge router until the rout-
er bit 22 touches the surface of the work-
piece. Let go of the release lever 16 again to
lock this plunging depth.
– Set the scale for coarse adjustment of the
depth-of-cut 6 to "0".
– Adjust the required depth-of-cut by turning
the adjustment knob for coarse adjustment 7
and reading the scale 6. Pay attention not to
readjust the rotatable scale 6.
– Lock the clamping lever for depth-of-cut
coarse adjustment 5 by turning in clockwise
direction and slide the router upward.
For deep cuts, it is recommended to carry out
several cuts, each with little material removal.
By using the step buffer 8, the cutting process
can be divided into several steps. For this, ad-
just the desired depth-of-cut with the lowest
step of the step buffer and select the higher
steps first for the initial cuts. The clearance of
the steps can be changed by screwing the ad-
justing screws further in or out.
After a trial cut, the depth-of-cut can be set ex-
actly to the desired measure by turning the ad-
justment knob 1; turn in clockwise direction to
increase the cutting depth and in anticlockwise
direction to decrease the cutting depth. The
scale 2 can be used for guidance. One full turn
corresponds with a setting range of 2.0 mm; a
graduation mark on the top edge of the scale 2
Bosch Power Tools