Tabla de contenido
Idiomas disponibles
Idiomas disponibles
grip the main handle/upper shaft and apply
adequate force on the upper handle pushing it
downwards, as shown in Fig H1.
Adjust the upper shaft angle upwards, put one
foot on the safety guard area of the trimmer
head, then grip the main handle, apply
adequate force to adjust, as shown in Fig. H2.
9. SPaCER GuaRd
Push the flower guard in when edging and
pull it before trimming, as shown in Figure
I. Before trimming or edging make sure the
flower guard is locked firmly in position.
oPErATIoN
waRNiNG: Always wear the eye
protection. Never lean over the trimmer
head. Rocks or debris can ricochet or be thrown
into eyes and face and cause blindness or other
serious injury. When operating unit, check for
the following:
Wear eye protection and heavy clothing. Hold
front handle with one hand and auxiliary handle
with the other hand. Keep unit below waist
12
12
level. Work only from your right to your left to
ensure debris is thrown away from you. Without
bending over, keep line near and parallel to the
ground (perpendicular when edging) and not
crowded into material being cut.
waRNiNG: make sure that line is
fed out before operation. make sure
motor is up to full speed before trimming
or edging.
waRNiNG: Use only 0.065"(1.65mm)
cutting line, diameter line. Other sizes of
line will not feed properly and will result in
improper cutting head function or can cause
serious injury. Do not use other material
such as wire, string, rope, etc. Wire can break
off during cutting and become a dangerous
projectile that can cause serious injury.
TRimmiNG
Hold the bottom of the trimmer head about
just above the ground and at a slight angle.
Allow only the tip of line to make contact with
the grass. Let the trimmer line work at its own
pace. Do not force trimmer line into work area.
2-in-1 Cordless Li-ion Grass Trimmer/Edger
Edging (See Fig J)
Change the tool from trimming to edging
mode by putting one foot on the motor
housing portion of the trimmer head (20)
while gripping the main handle/upper shaft
apply adequate force on the upper handle
pushing it downwards, as shown in Fig H1.
Make sure to adjust trimmer head angle to be
in the lowest horizontal setting. Then, holding
the lower housing then pull upwards the
upper shaft, then rotate 90 degree clockwise.
(Fig F1,)
Then position the wheel on the ground for
edge mode. The guard has two white line
guides to indicate the cutting line position.
Align these marks with the edge of your lawn.
While edging, only allow the tip of the line to
make contact with area being worked. Do not
force the line. The edging wheels help protect
the unit and keep the unit from contacting the
ground. Take extra caution while edging as
objects can be thrown from the trimmer line.
auTomaTiC LiNE FEEd SySTEm
When initially switching on the trimmer, a
small length of line is fed out. Each time the
tools is started from rest it will advance about
.25 inches of trimmer line.
A 'clattering' noise will be heard when the
lines hit the line cutter. DO NOT BE ALARMED
this is quit normal. After about 5 seconds the
line will be cut to the correct length and the
noise will reduce as the motor receives full
speed.
If the noise of the line being cut can't be
heard, more line will need to be fed out.
To feed more line, it is first necessary to allow
the trimmer to stop completely; it must come
to a complete rest, then restart, allowing the
motor to reach full speed.
Repeat above until you hear the line hitting
against the line cutter. (Do not repeat this
procedure more than 6 times)
To maNuaLLy FEEd THE LiNE (See Fig
k1)
Turn off the trimmer and remove the battery
If required, line can be feed out manually
To operate, press and release manual line feed
button (16), while gently pulling out the line
EN
Tabla de contenido
