Assembly - Scheppach DP19Vario Traduccion Del Manual De Instrucciones Originales

• Familiarise yourself with the product by means of the
operating instructions before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
m WARNING!
The device and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!

8. Assembly

Column and machine foot, fig. 3
1. Set the machine foot (1) down on the ground or
the workbench.
2. Place the column (2) on the base plate so that the
holes on the column (2) align with the holes on the
base plate (1).
3. Screw the four hexagonal bolts (17) to fasten the
column into the base plate and tighten them using a
hexagon spanner.
Removing the toothed rack, Fig. 4
In order to be able to install your drill, you must first
remove the toothed rack (D).
1. Use an Allen key (WAF3) to remove the ring (E)
and pull this off the column (2).
2. Now pull the toothed rack (D) out.
Installing the drilling table holder, Fig. 5 - 7
1. Insert the toothed rack (D) into the groove on the
drilling table holder (4).
2. Align the toothed rack (D) centrally in relation to
the drilling table holder (4).
3. When bringing the toothed rack (D) together with-
in the groove, ensure that the tooth meshing be-
tween the toothed rack and the drilling table holder
(4) is correct.
4. Now place the drilling table holder (4) with the
toothed rack (D) on the column (2) and guide the
toothed rack (D) into the bottom rack guide on the
column foot.
5. Use the ring (E) to secure the toothed rack (D). En-
sure that the toothed rack guide on the ring (E) is
pointing downwards. Tighten the integrated Allen
screw to affix the ring (E).
30 | GB
6. Place the crank handle (16) on the shaft of the
drilling table holder (4) and secure it with the hex-
agon socket screw. Use the Allen key (B) for this
purpose
7. Screw the clamping handle (3) into the drilling ta-
ble holder (4).
Installing the machine head and column, Fig. 8
1. Place the machine head (13) on the column (2).
2. Align the drill's spindle with the table and the base
plate and tighten the Allen screw that is located on
the side of the machine head. (Allen key WAF4 / A)
Installing the handle, Fig. 9+10
1. Screw three handles (10) tight in the handle brack-
et's thread. Use the hexagon spanner to do this.
2. Screw the remaining speed adjustment lever (han-
dle) (6) into the handle bracket for speed adjust-
ment. Use the hexagon spanner to do this.
Installing the folding swarf protector and the drill
chuck, Fig. 11
1. Push the folding swarf protector (11) onto the spin-
dle on the machine head and use a Phillips head
screwdriver to secure it.
Installing the chuck, Fig. 12
1. Clean the conical hole in the chuck and the spindle
cone with a clean piece of fabric. Ensure that no
particles of dirt remain on the surface. The small-
est amount of contamination on one of the surfac-
es prevents the chuck holding properly. This can
cause the drill bit to wobble. If the conical hole in
the chuck is extremely contaminated, use a clean-
ing agent on a clean piece of fabric.
2. Push the chuck onto the spindle lug as far as pos-
sible.
3. Turn the outer ring on the chuck anti-clockwise
(when viewed from above) and open the jaws on
the chuck.
4. Place a piece of wood on the machine table and
lower the spindle until it touches the piece of wood.
Press tight so that the chuck is secure.
Inserting/replacing the battery: Laser operation
Fig. 13
1. Inserting/replacing the battery: Switch off the laser
Insert or remove the battery compartment cover
(14.1). Remove batteries and replace with new
ones (2 AA batteries).
www.scheppach.com