Preparing The Appliance - Kärcher T 350 T-Racer Manual De Instrucciones

Preparing the Appliance

Selecting the high pressure nozzles
You need to use the matching high pressure nozzles to
ensure that your high pressure cleaner works properly.
Note
Delivery rate (l/min): See operating instructions or type
plate of your pressure washer.
Pressure washer with delivery rate of less than 5.8 l/
min (350 l/h)
e.g.: K 2 – K 3
 Use green high-pressure nozzles.
Pressure washer with delivery rate from 5.8 l/min
(351 l/h) to 7.5 l/min (450 l/h)
e.g.: K 3 – K 5
 Use purple high-pressure nozzles.
Pressure washer with delivery rate of more than
7.5 l/min (450 l/h)
e.g.: K 6 – K 7
 Use beige high-pressure nozzles.
Note
The beige high-pressure nozzles are already installed.
Changing the high pressure nozzles
 Illustration
a Remove the clip.
b Pull out the high-pressure nozzle.
c Insert the nozzle.
d Reinsert the clip.
Application
Note: Always use Kärcher water filter (order no. 4.730-
059.0) during suction operations of the high-pressure
cleaner.
Do not operate the pressure washer at the Eco level if
you wish to achieve an optimum cleaning result.
Cleaning floor surfaces
Fasten the T-Racer to the high-pressure gun using the
extension pipes.
 Illustration
1 Press the extension pipe into the bayonet catch of
the T-Racer.
2 Turn it by 90° until it locks into place.
3 Tighten the union nut.
Repeat this process even for the other joints.
Tips for cleaning
 Outdoor surfaces should be swept before the T-
Racer is used to avoid damaging the high-pressure
nozzles.
 Prior to use on sensitive surfaces (e.g. wooden sur-
faces), test the product on an imperceptible spot, in
order to promptly detect any changes in the sur-
face.
 The T-Racer is not suited for scouring or scrubbing!
 Guide the T-Racer over the surface without effort.
 Do not remain at one spot; always keep moving
during cleaning.
 Adjust the twist grip "Power" in accordance with the
surface to be cleaned.
 Illustration
All manuals and user guides at all-guides.com
Do not run over protruding corners!
Fasten the T-Racer directly to the high-pressure gun.
1
2
3
 Illustration
Always hold the T-Racer at the handle while cleaning
the walls.
 Adjust the twist grip "Power" in accordance with the
The cleaning pressure is adjusted with the twist grip
Power via a bypass system.
Sturdy surfaces (e.g. tiles, concrete, stone)
 Illustration
Sensitive surfaces (e.g. wood)
 Illustration
The T-Racer can be parked on level surfaces in the
parking position during breaks.
 Illustration
Remove the high-pressure gun from the extension
tubes.
Push the extension tubes to the front.
You can use the extension pipes with any other Kärcher
accessory.
Use a moist cloth and clean the appliance after use.
Store the appliance in a frost free area.
The device can be suspended into the KÄRCHER or-
ganiser for storage.
Pressure washer does not build up pressure or is
pulsating.
 Dismantle the high-pressure nozzles, check the
You need to use the matching high pressure noz-
zles to ensure that your high pressure cleaner
works properly.
 Select and install the high-pressure nozzles in ac-
– 2
EN
CAUTION
Cleaning wall surfaces
Press the bayonet connection of the T-Racer into
the connection of the high-pressure gun.
Turn it by 90° until it locks into place.
Tighten the union nut.
CAUTION
surface to be cleaned.
Control elements
Set turning handle "power" to "HARD".
For the effective cleaning of hard-to-remove con-
tamination.
Set turning handle "power" to "SOFT".
For the gentle cleaning of sensitive surfaces.
Parking position
Tip
Care
Troubleshooting
high-pressure nozzles for damage, rinse the T-
Racer with clean water then reinstall the high-pres-
sure nozzles.
cordance with the pressure washer used.
7