Tabla de contenido
Idiomas disponibles
Idiomas disponibles
EN
PT
Always read the
IMPORTANT:
instructions before you start using
your power tool.
BASIC SAFETY
PRECAUTIONS
1. Keep the work area clean. A
cluttered site can cause damage.
2. Do not use power tools in damp
or wet locations. Do not expose
power tools to rain. Keep the
workplace well lit. Do not use in
locations with gas / flammable
liquids.
3. When working with the machine,
do not touch other devices
connected to the mains.
4. Do not allow children to remain
close to the workplace. All people
should stay away.
5. You should keep all tools in a dry,
high and locked.
6. Get a job with better quality if
the suit the speed of the machine.
Avoid unnecessary burdens that
may endanger the operator and the
power tool.
7. Do not force small tools and
accessories to perform the work of
larger machines, and do not use for
work inadequate.
8. Do not wear loose clothing or
jewelery, they can become trapped
in the tool. We recommend the use
of gloves and work shoes. Long hair
should also be arrested.
9. Always use eye protection. If
dust, also use mask.
10. Do not hold the tool by the cord.
Should not turn off the electrical
current to stop the tool. This
procedure should be done on the
switch. Keep cord away from heat,
fuel and sharp edges.
11. Keep yourself in balance.
12. Keep tools clean for better and
safer performance. Follow the
maintenance instructions. Inspect
cords regularly and replace them
if damaged. Keep your hands dry,
clean and free of oil.
13. Disconnect the tool from the
mains when not being used, and
when replacing the accessories
(such as drills, discs, etc ...)
14. Get used to check that adjusting
keys are with the power tool.
15. If the tool is connected to the
mains, do not transport with fingers
in contact with the switch. On the
other hand, make sure the switch is
off when plugging in the mains.
16. If you need an extension make
sure that the wire of the same
section has a size equal to or
greater than the cable from the
power tool.
17. Stay alert, attentive to his work,
and use common sense. Do not
continue to work if you are tired.
18. Before starting work with any
tool, must prove that there is no
damaged parts. Carefully check the
installation and tuning of all moving
parts.
19. Any damaged part should be
properly repaired or replaced by a
qualified technician. Do not use the
tool if the switch is not working.
20. The use of an accessory
inappropriate represents a potential
risk to the user.
21. This tool complies with the
safety regulations in force. Your
repair should only be performed by
a qualified technician. Otherwise,
the risk to the user is real.
STRUCTURE AND
FUNCTIONS
The grinders are power tools class
II with double insulation structure.
ADDITIONAL SAFETY
RULES
1. It is recommended that the user
use goggles.
2. In operation, the cable should be
in the rear of the tool to avoid being
damaged.
3. In operation, should not strike the
workpiece with the abrasive disc.
To get a good result, the inclination
between the disc and the workpiece
should be 15 ° to 30 °.
4. Do not drag the tool by the cord.
5. Before using the tool ensures that
the protective device of the disk is
implemented well. The use of the tool
without the guard is strictly prohibited.
6. Before commencing operations,
make sure that the disc brake button
is OFF.
7. It is forbidden to use the disc
brake button to stop the disc in
progress. This will damage the tool
and can be extremely dangerous to
everyone around you.
8. It is important to choose a disc
whose safety speed is not less than
the speed of the tool.
9. When inspection, adjustment and
replacement of the disc, be sure
that the tool is not connected to the
mains.
10. Before starting work, carefully
check the disc status. This should
not be used to perform a crevice.
11. Do not cut. Just grinding.
9
Tabla de contenido
