SIOUX SBS05S18 Manual De Instrucciones página 3

Tools with the actuator left in the "ON" position when an unexpected air pressure loss occurs can start unexpectedly when the air
pressure is restored.
Release the actuator if an unexpected loss of air pressure occurs.
Unexpected tool starts can cause injury.
Tools with the actuator left in the "on" position can cause unexpected starts when the tool is connected to the air supply.
Be sure actuator is off before hooking up air.
Unexpected starts can cause injury.
Sanders may coast for a short time after the trigger is released.
Be sure tool has come to a complete stop before setting it aside. Do not use tools or accessories that have been damaged.
Sanders that do not come to a complete stop before setting aside can cause injury.
Abrasive belts that are worn, damaged, nicked, bent, warped or burred can cause the sanding disc to tear and burst.
Do not use abrasive belts that are worn, damaged, nicked, bent, warped or burred.
Abrasive belts that burst can cause injury.
Tools left connected to the air supply while making adjustments, changing accessories, or doing any maintenance or service can start
unexpectedly.
Always remove the tool from the air supply and activate the trigger to bleed the airline before making adjustments, changing
accessories, or doing any maintenance or service.
Tools that start unexpectedly can cause injury.
The use of any accessory with this tool not provided or specified by Sioux Tools can perform unpredictably.
Use only accessories provided or specified by Sioux Tools.
Tools that perform unpredictably can cause injury.
Be aware of hazards of operating the tool.
Operators and maintenance personnel shall be able to handle the bulk, weight, and power of the tool. There is a risk of
electrostatic discharge if used on plastic or other non-conductive materials.
Tools shall be periodically inspected to ensure ratings and markings are legible.
Be aware of your surroundings when operating the tool.
Slips, trips, and falls are a major cause of workplace injury.
Be aware of slippery surfaces caused by use of the tool and also of trip hazards caused by the air hoses.
When disposing of a tool, do it in a way that does not harm personnel or the environment. Verify that operators, and maintenance
personnel, should be able to handle the bulk, weight, and power of these sanders before using or servicing.
INTENDED USE
This tool is intended to be used with abrasive sanding discs for the finish sanding of materials such as wood, metal, fiberglass and similar materials. If it
is used for anything else, it is considered misuse, creates a hazard and may void the warranty.
AIR SUPPLY
The efficiency and life of this tool depend on the proper supply of clean, dry air at a maximum of 90 PSI. The use of an airline filter, pressure regulator,
and lubricator is recommended. Before connecting to tools, blow out the airline to remove water and dirt that may have accumulated.
HOSE AND HOSE CONNECTIONS
The air supply hose recommended is 3/8" (10mm) I.D. If an extension hose is necessary, use 1/2" (13mm) ID hose with couplings not less than 3/8"
(10mm) I.D. The tool inlet thread is 1/4" NPT.
LUBRICATION
For maximum performance and tool life, an airline lubricator, set to deliver 1 drop per minute. SIOUX No. 288 Air Motor Oil is recommended. If an airline
lubricator is not used, add 8 to 10 drops of air motor oil to the air inlet at the start of the day and run the tool for 10-20 seconds.
Do not over lubricate because excess oil may contaminate the surface being sanded.
MAINTENANCE
Water, dust and other airline contaminants can cause rust and vane sticking. After long idle periods, flush the tool with a few drops of oil and run for 10
seconds. This will help remove contaminants and reduce the formation of rust. Check the free tool speed regularly and be sure it does not exceed the
nameplate speed.
OPERATION
Speed of the tool may be adjusted by turning the regulator located near the air inlet.
Depress the trigger to start the tool.
Run tool at a low speed and use the sanding arm adjustment knob to ensure that the sanding belt remains centered on the roller during tool operation,
this may need to be adjusted when a new belt is installed.
When changing out sanding belts, disconnect tool from air supply, then remove the sander guard. Next, press the sanding arm towards the center of
the tool to allow belts to be removed & installed.
Weight
Catalog No.
(lbs/kg)
SBS05S18 TBA
Form ZCE868
Disconnect tool from air supply before installing or removing wheel or making any adjustments
Be sure the pad is the correct size for the tool.
A mismatch between tool and pad will cause excessive vibration.
NOISE AND VIBRATION READINGS
Sound Pressure dBA
(per EN ISO 15744)
TBA
WARNING
WARNING
Sound Power dBA
Uncertainty (dBA)
(per EN ISO 15744)
TBA TBA
3
Vibration m/s Uncertainty m/s
2
(per EN ISO 28927-3) (per EN 12096)
TBA TBA
Date 2022January14/A
2