Using The Product - LUND 67700 Manual De Instrucciones

GB

USING THE PRODUCT

Preparing the product for operation
The product must be unpacked and all parts of the packaging completely removed. It is recommended to keep the packaging, as
it can be helpful in further transporting and storing of the product.
Check the product for damage. In the event of any damage being found, do not use the product, before the damage has been
remedied or the damaged components changed for new components, free of defects.
Clean the product, according to the instructions specifi ed in the "Product Maintenance" section.
Caution! Make sure that the power cord is unplugged from the wall socket, before attempting to install or remove any attachment.
Install the selected attachment, according to its intended use. Place the attachment housing onto the mounting of the drive hous-
ing, so that the mounting edge of the attachment fi ts tight along its entire circumference, and then rotate it all the way (II). Make
sure that the attachment is not disconnected on its own, during operation. If an attachment cannot be detached by pulling it away
from the drive housing, and its edge fi ts tight along its entire circumference to the drive housing, then it has been installed correctly.
If this is not the case, repeat all installation steps.
If a cutting attachment is used, it may only be used together with the supplied container. Place the container on a fl at, level, and
hard surface. Then, remove the holder for attachments, before use, and ensure that the container lid is tightly closed.
The lid of the container for the cutting attachment should be mounted in the same way, as the attachment for the drive housing.
The transparent wall of the container makes it easier to match the projections on the wall with the guides on the lid. The edge of
a correctly installed lid rests along its entire circumference on the edge of the container wall (III).
The lid of the blender container should be mounted in such a way that its edge rests on the edge of the container wall along its
entire circumference. The indicator on the lock of the lid should display the symbol of an open padlock on the lid (IV). Next, press
and hold the raised lock of the lid, and then rotate the lid, until the indicator is in line with the symbol of the locked padlock. Then,
release the lock and lower it, to prevent the lid from opening accidentally.
The mixing attachment is used for shredding vegetables and fruits, preparing sauces, mixing of liquids, e.g. soups, creams, etc.
The cutting attachment is used for chopping, mincing meat, and making pastes from hard food products.
The whipping unit is used to prepare egg foam, whip cream, mix thin doughs, e.g. pancakes, or whisk eggs.
The blender container may only be used with a plate, or alternatively with the cutting attachment. During operation, food may only
be introduced via the opening in the lid of the container. To cram it, use the pusher provided. Using other objects or hands for this
purpose may result in damaging the product or serious injury.
If the product is supplied with a container with a graduated scale, it can be used as a dish to prepare dishes. Commercially avail-
able containers can also be used for this purpose. The cutting attachment may only be used together with the supplied container
with a lid.
The connection between the lid and the container is not air-tight. It is possible that contents of the container may start escaping
through the gap between the lid and the container. In that case, reduce the amount of food in the container.
The cutting attachment for the bottle has a gasket, which ensures that the lid is tightly connected to the bottle. The attachment
is attached to the bottle by screwing it on. Use suffi cient force, when screwing on the bottle, to make sure that the bottle with its
attachment facing downwards shows no signs of leakage. You can mount the entire unit onto the drive housing, only after making
sure that the connection between the lid and the bottle is tight enough. Use the attachment in such a way that the bottom of the
bottle is facing up. Remove the whole unit from the drive housing and then replace the cutting attachment with the supplied lid,
immediately after preparing food inside the bottle. This way, you can take the prepared food with you, without having to use other
dishes.
None of the attachments is designed for shredding ice cubes.
Using the Product
Install the selected attachment.
Plug the power cord into the power socket, but do not touch the switch.
If a mixing or whipping attachment is fi tted, insert the end of the attachment into the container with food, and start the unit by
pressing and holding down the switch. The product has two switches: the upper one that enables working at the speed set by the
controller, and the lower one that enables working at the maximum speed.
The period of time during which the product is used must not exceed 1 minute. Then, the drive must be allowed to cool down for
at least 4 minutes.
The product is switched off by releasing the switch. Wait until the moving parts of the attachments have stopped rotating, and then
pull the power cord out of the socket, and remove the attachment from the container with food and/or remove the attachment.
If attachments with blades are used, it is advisable to use a lower rotational speed at the beginning of the operation, and then
increase it gradually during operation, until satisfactory results are obtained.
If lower speed is used for all attachments, it will reduce the splashing of liquid food and loose products.
Product maintenance
CAUTION! Before cleaning, switch the product off , unplug the power cord from the wall socket, wait for the unit to cool down, and
then proceed with maintenance.
O R I G I N A L I N S T R U C T I O N S
11