GBC SmartPunch Plus Manual De Instrucciones De Operación página 8

Changing the Settings on the LCD panel
A. When a Punch Die is inserted
i) Alignment
Alignment is the distance of the front punched hole from the side
edge of the sheet. Follow the LCD screen to modify this setting.
This value can be adjusted ±2.0mm.
ii) Backgage
Backgage is the distance of the punched hole(s) from the trail edge
of the sheet. Follow the LCD screen ito modify this setting. Refer to
Table 3 for the range of adjustment depending on the die inserted.
The settings for backgage MID L and MID XL adjust the backgage
of the mid punch holes for double punch mode for Large (L) and
Extra Large (XL) sheets. MID L and MID XL function the same as
the regular backgage depth but adjust the position of the middle
punch. MID L sheets are LTR, Legal, 9x12, A4 & SRA4 in the short
edge feed direction. MID XL are 11x17,12x18, A4, A3, & SRA3 all
in the short edge feed direction.
iii) Clear Cover
Use this setting to offset the Backgage depth and Alignment setting
for Clear Cover media in addition to the standard backgage &
alignment setting. Adjusting this offset does not affect the standard
Backgage and Alignment setting.
iv) Full Bleed
Use this setting to define how paper of length 9" or 223mm will be
treated by the punch. If the sheet of this length being sent is full
cover (9" x 11") then choose the Tab/Full Cover option. If the sheet
of this length is 9" x 12" or 225 x 320mm then select Full Bleed.
v) Saddle Punch Adjustment
This will adjust the position of the punches on either side from the
center of the sheet. Follow the LCD screen to modify this setting.
Refer to Table 2 for the range of adjustment depending on the paper
size being run.
B. When a Crease Die is inserted
i) Center Crease Adjustment
This will adjust the position of the crease from the center of the
sheet. Follow the LCD screen to modify this setting. Refer to Table
2 for the range of adjustment depending on the paper size being
run.
ii) Book Crease Adjustment
This will adjust the position of the creases either side from the
center of the sheet. Follow the LCD screen to modify this setting.
Refer to Table 2 for the range of adjustment depending on the paper
size being run.
iii) C-Fold Crease Adjustment
This mode will place the creases at 1/3 and 2/3 locations on the
sheet. The creases can be adjusted from these default positions.
Follow the LCD screen to modify this setting. Refer to Table 2 for
the range of adjustment depending on the paper size being run.
SmartPunch Plus
C. When a Perforation Die is Inserted
i) Center Perf Adjustment
This will adjust the position of the perforation from the center of the
sheet. Follow the LCD screen to modify this setting. Refer to Table
2 for the range of adjustment depending on the paper size being
run.
ii) Single Perforation Adjustment
This will adjust the position of the single perforation anywhere from
the center of the sheet to the trail edge. Follow the LCD screen to
modify this setting. Refer to Table 2 for the range of adjustment
depending on the paper size being run. Note that if the Single Perf
Adjustment is set outside the allowable range for your sheet, the
sheet will pass through without perforation and "Out of Range
Adjustment" will appear on the screen.
iii) Double Perforation Adjustment
This will adjust the position of two perforations anywhere from the
center of the sheet to the trail edge. Follow the LCD screen to
modify this setting. Refer to Table 2 for the range of adjustment
depending on the paper size being run. Note that if the Double Perf
Adjustment is set outside the allowable range for your sheet, the
sheet will pass through without perforation and "Out of Range
Adjustment" will appear on the screen.
D. Language
The LCD panel can be configured to display one of the following
languages: English; Francais; Espanol; Deutsch or Italiano.
E. Units
The LCD panel can be configured to display units in mm or Inches.
Displaying Information on the LCD Panel
When the Info option is selected from the home screen the following
information will be shown.
1. Die type
This is type of die set currently installed in the punch. No die
will be displayed if a die is not installed.
2. Die cycles
This is the total number of sheets punched with the currently
installed die set.
3. Punch cycles/Perf cycles/Crease cycles
This is the total number of punched sheets the system has
processed for each type of operation.
4. Firmware
This displays the current level of Main & Communication
(Comm) firmware of SmartPunch Plus.
GB
8