Lenco SCD-680 Manual Del Usuario página 6

press Skip down (11) or Skip up
stereo signals are weak and noisy. It is preferable to change the FM mode by same procedure.
Hints for best reception:‐
FM: the receiver has rod antenna (6) hanging at the rear cabinet. It should be totally extended for best reception.
Radio data system (RDS)
This is the features to display the information which released from the radio broadcast and will showed on LCD display step by
step as below by pressing the Play mode/info button (21) continuously.
Radio text  program type  frequency  mono/stereo  time  date
Digital audio broadcasting (DAB) radio
1. Set the unit to DAB mode by press Function button (9).
2. Press the Play/pause
(11) or Skip up
selected channel.
3. Press the Play mode/info button (21) continuously to check the below info released by DAB.
signal strength  program type  Group name  frequency  signal error  transfer rate  time date
4. Adjust volume knob (14) for the desired volume level.
Dynamic range control
This apparatus provide three dynamic range mode to match different program type in DAB mode.
1. In DAB mode, press "Menu/Mem/clk‐adj" button (12) to enter the "Menu", then press Skip down
(19) button to select "DRC".
2. Press "Stop/Enter" button (10) to enter the "DRC" setting, then press Skip down
select "DRC high/low/off" mode. Then press "Stop/Enter" button (10) to confirm the setting.
3. In any state press "Menu/Mem/clk‐adj" button (12) to quit the setting mode
Language setting
This apparatus provide 4 language for FM/DAB operation display.
1. In DAB/FM mode, press "Menu/Mem/clk‐adj" button (12) to enter the "Menu", then press Skip down
(19) button to select "Language".
2. Press "Stop/Enter" button (10) to enter the "language" setting, then press Skip down
to select your desired between English/French/German/Italian. Then press "Stop/Enter" button (10) to confirm the setting.
3. In any state press "Menu/Mem/clk‐adj" button (12) to quit the setting mode
Preset stations
You can store up to total of 20 radio stations in the memory (10‐FM/10‐DAB).
1. Set to FM/DAB mode
2. Turn to the desired radio station by "manual" or "auto" tuning method.
3. Press and hold the "Mem/clk‐adj" button (12) to enable memory state.
4. Press Skip down (11) or Skip up
5. Press "Stop/Enter" button (10) to confirm the setting.
6. Repeat step 2 to 5 to store other stations.
Recall preset stations
1. Set to FM/DAB mode
2. Press Pre‐up button (20) to recall the stored station.
3. Press Skip down (11) or Skip up
4. Press "Stop/Enter" button (10) again to confirm the recall station.
DAB/FM reset:
If case would like to erase all the FM/DAB programed memory station, operation as below.
1. Set in DAB or FM mode, press "Menu/Mem/clk‐adj" button (12) to enter the "Menu", then press Skip down
Skip up (19) button to select "System".
2. Press "Stop/Enter" button (10) to enter the "System" setting, then press Skip down
select "Factory reset". Then press "Stop/Enter" button (10) to confirm the factory reset.
3. Apparatus will erase all the programed memory station, perform the preset station again as above.
Playing CD/MP3 disc
 Getting start
1. Press Function button (9) to select CD mode.
2. Open the CD door by pressing the CD door open/close (7). Put a CD disc into the compartment and close the CD door.
3. Focus search is performance if disc is inside. Total number of tracks is read.
Version: 1.0
(19) again to select FM stereo, then press Enter button (10) to confirm. When
/Scan button (18) once, unit will start to full scan from range 11b‐12d one time. Press Skip down
(19) button to select your desired DAB channel then press "Stop/Enter" button (10) to confirm the
(19) button to select the desired station memory for storage.
(19) button to select the desired recall station.
(11) or Skip up
(11) or Skip up
6
(11) or Skip up
(19) button to
(11) or Skip up
(11) or Skip up (19) button
(11) or
(19) button to