Parts List - LUND SR2 Instrucciones De Instalación

PARTS LIST:

2 SR2 Running Boards
4 Mounting Brackets
1 Driver/left side Center Mounting Bracket
1 Passenger/right side Center Mounting Bracket
6 8-1.25mm Double Bolt Plates
10 8mm Clip-On Nuts
10 8mm x 30mm Hex Bolts
Passenger/Right Side
Center Bracket
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION.
2. Starting on the driver/left side front of the vehicle, locate the (2) holes in the bottom of the body panel,
(pinch weld), toward the front tire, (Figures 1 & 2). Next locate the rectangular opening and (2) small
holes in the inner body panel directly above the holes in the pinch weld, (Figures 1 & 2). NOTE: The
holes in the inner panel may be covered with sealing tape or insulation.
3. Slide (1) 8mm Clip Nut into the rectangular opening with the nut towards the inside. Line up the
threaded nut on the clip with the round hole, (Figure 3). Repeat to install the 2nd 8mm Clip Nut in
remaining hole location.
4. Select (1) Universal front/rear Mounting Bracket. Attach the Bracket to the (2) Clip Nuts with the
included (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm x 28mm Large Flat
Washers, (Figures 4 & 6). NOTE: Depending on model and year, the brake cable may be run on the
outside of the Bracket. Do not tighten hardware at this time.
5. Align the bottom holes in the front Bracket with the (2) holes in the pinch weld. Attach the Bracket to the
pinch weld using the included (2) 8mm x 25mm Hex Bolts, (4) 8mm x 24mm STD Flat Washers, (2)
8mm Lock Washers and (2) 8mm Hex Nuts, (Figures 5 & 6). NOTE: Insert the bolts up from the
bottom of the pinch weld and through the Bracket.
6. Move along the cab to the center mounting location, (Figures 1 & 7). Locate the (2) holes in the pinch
weld similar to the front location. Insert (1) 8mm Clip Nut into the rectangular opening and up to the
single small round hole in the body panel, (Figure 7). Attach the top of the center Bracket to the Clip
Nut with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm x 28mm Large Flat Washer,
(Figures 8 & 9). Line up the hole in the Bracket with the forward hole in the pinch weld. Attach the
Bracket to the pinch weld with (1) 8mm x 25mm Hex Bolt, (2) 8mm x 24mm Small Flat Washers, (1)
8mm Lock Washer and (1) 8mm Hex Nut, (Figures 8 & 9). Do not tighten hardware at this time.
(6) 8mm Double
Bolt Plates
(4) Universal Left or Right
Mounting Brackets
Page 1 of 5
09-14 FORD F-150 SUPER CREW CAB
10 8mm x 25mm Hex Bolts
10 8mm x 28mm x 3mm Flat Washers
32 8mm x 24mm x 2mm Flat Washers
20 8mm Lock Washers
10 8mm Hex Nuts
12 8-1.25mm Nylon Lock Nuts
SR2 RUNNING BOARD
Driver/Left Side
Center Bracket
11/30/17 (RA)