Using The Hand Blender - Ritter ESM 50 Instrucciones De Montaje Y De Uso

USING THE HAND
BLENDER
Connecting/replacing an
attachment
CAUTION, risk of injury:
– Switch the blender (1) off
before connecting or remov-
ing attachments.
– Keep your fingers away from
the buttons to prevent the
appliance from switching on
accidentally.
– The blades on the attach-
ments are very sharp! Never
touch these blades with your
bare hands.
B
To connect one of the
attachments (9 – 12), hold the
attachment with a tea towel to
protect your hands and mount it
on the drive shaft (3b).
Make sure that the drive shaft
pin (3a) fits snugly into the slot on
the attachment (3c).
B
To remove the attachment,
hold it with a tea towel to protect
your hands and pull it carefully off
the drive shaft.

Using the hand blender

CAUTION, risk of injury:
Do not use your hands to
remove any pieces of food that
become jammed in the blades!
Use a blunt object (e.g. a small
wooden implement) to do this
instead.
• Place the food in the blending
cup (14) or another flat-bottomed
container. Do not start using the
hand blender (1) until it is posi-
tioned inside the container.
Info:
– When using the blending cup:
Do not fill the blending cup to
the brim. During blending, the
liquid in the cup will creep up
the sides and may splash out.
– Tall, narrow containers are
more suitable than flat, wide
ones.
– If using a coated container,
take care not to damage the
coating during blending.
C
To switch it on, first press and
hold down the unlock button (7).
Then, within 2 seconds, press the
power button (8).
• Keep the unlock button
pressed during operation.
The hand blender begins to oper-
ate at the highest speed setting.
The LEDs on the LED display (6)
light up (the number that light up
depends on the current battery
level).
Info:
To prevent the hand blender
from overloading, the appliance
will switch off automatically if it
becomes overheated, if a blade
becomes jammed or if the appli-
ance is operated continuously
for more than 4 minutes. After
it switches off, all LEDs flash
slowly. You can then switch the
blender on again and continue
using it.
• Adjust the speed if necessary:
Briefly press the power button.
This reduces the speed.
Info:
The next speed setting after the
lowest speed setting is the high-
est speed setting.
• Release the unlock button to
switch the appliance off.
Displaying the current battery
level
• Briefly press the unlock but-
ton (7).
The number of LEDs that light up
indicates the current battery level.
CLEANING
CAUTION, risk of injury:
– Keep your fingers away from
the buttons to prevent the
appliance from switching on
accidentally.
– The blades on the attach-
ments are very sharp! Never
touch these blades with your
bare hands.
To prevent the accumulation
of food residue, clean the
blender (1) thoroughly after each
use:
• Immerse the blender shaft (3)
of the hand blender in the
blending cup (14) or another
container filled with warm water
and detergent.
• Switch the hand blender on.
Allow it to operate for a short
period in the detergent solution.
• Fill the blending cup or con-
tainer with clean, clear water and
allow the hand blender to operate
in the water for a short period.
• To ensure that all food residue
is removed, detach the blender
attachment (see „Connecting/
replacing an attachment") and
clean it.
• Use a damp cloth to wipe
down the motor unit (2), blender
shaft and charging station (13) if
necessary.
NOTE, risk of damage to the
hand blender:
– Do not use any scouring
agents, abrasive cleansers,
sponges with rough surfaces
or hard brushes.
– The hand blender is not
suitable for washing in a
dishwasher.
– Do not leave the blender
shaft (3) sitting in liquid for a
long time, as this may cause
discolouration.
• Dry all parts that you have
washed.
English
15