Kraftixx TKS 254/2000 Manual De Instrucciones Original página 31

leg (29) engages properly.
•
Plug the rubber feet (13) onto the legs (29).
6.2 Assembling the table width extension/
length extension (Fig. 5, 6)
•
Use the hexagon screw (46), washer (49),
spring washer (50) and nut (51) to fasten the
table width extensions (33) loosely to the saw
table (1).
•
Remove the hexagon screw (46) from the
base frame (47) on the left and right-hand
side to enable the struts (32) and the base
frame (47) to be fitted.
•
Fasten the struts (32) loosely to the base
frame (47) with hexagon screws (46), but do
not tighten.
•
Use the hexagon screw (46), washer (49),
spring washer (50) and nut (51) to screw the
struts (32) loosely to the table width extensi-
ons (33).
•
Use the hexagon screw (46), washer (49),
spring washer (50) and nut (51) to fasten the
table length extension (34) loosely to the saw
table (1).
•
Remove the hexagon screws (46) on the back
of the base frame (47).
•
Fasten the struts (36) loosely to the base
frame (47) with hexagon screws (46), but do
not tighten.
•
Use the hexagon screw (46), washer (49),
spring washer (50) and nut (51) to screw the
struts (36) loosely to the table length extensi-
on (34).
•
Align the table width extensions (33) and the
table length extension (34) level with the saw
table (1).
•
Then tighten the screw connections referred
to in 6.2. Use both the wrenches (38) and (39)
to do this.
6.3 Standing the bench-type circular saw up-
right (2, 7-9)
•
Turn the machine over so that it stands on its
legs (29).
•
The bench-type circular saw must be stood
on a flat surface.
•
Then tighten all loose screw connections. Use
both the wrenches (38) and (39) to do this.
•
Screw the additional legs (37 to the rear legs
(29) so that they point towards the rear of the
machine. Use the lock bolts (48), washers
(49), spring washers (50) and nuts (51) to fas-
ten them.
•
Warning! Don not fit the additional legs (37)
too far away from the surface on which the
Anl_TKS_254-2000_SPK7.indb 31
GB
machine stands; they are intended to provide
protection against tipping over.
•
Before you can fit the container for cutting
residues (59), fasten the screws (52) and nuts
(53) to the table width extension (33) and ta-
ble length extension (34) as shown in Fig. 9a
and 9b.
•
Attach the container for cutting residues (59)
to the screws (52) by the eyelets.
6.4 Changing the table insert (Fig. 10)
•
To prevent increased likelihood of injury, the
table insert should be changed whenever it is
worn or damaged.
•
Remove the saw blade guard (2) and the la-
ser unit (54) (see 6.7, 6.6).
•
Remove the countersunk head screws (17).
•
Lift out the table insert (6) at the back of the
saw table (1). Then pull the table insert (6)
towards the back until you can take out the ta-
ble insert (6) with the pin on the side through
the recess on the saw table (1).
•
Fit the replacement table insert in reverse
order.
6.5 Fitting/replacing the splitter (Fig. 11)
•
Important! In the as-delivered state the splitter
(5) is in the transport position. Always fasten
the splitter in the top position, as described
below.
•
Using the crank (10), set the blade (4) to max.
cutting depth, move to 0° position and lock in
place.
•
Remove the saw blade guard (2) and the la-
ser unit (54) (see 6.7, 6.6).
•
Take out the table insert (6) (see 6.4).
•
Unscrew the fastening screw (19) and remo-
ve the fastening plate (40).
•
Fit the splitter (5) and fasten it loosely with the
fastening plate (40) and fastening screw (19).
•
Important! The splitter (5) must be fastened in
the top position to enable the maximum cut-
ting capacity to be realized.
•
Push the splitter (5) right up to the top and
tighten the fastening screw (19) securely.
Make sure that the splitter (5) has been fitted
straight and not wobbly.
•
The splitter (5) must be positioned in the cen-
ter along an imaginary line extending behind
the saw blade (4), so that it is not possible for
the material to get jammed.
•
The gap between the blade (4) and the split-
ter (5) should be 3 mm to 8 mm. (Fig. 11c).
•
Refit the table insert (6), laser unit (54) and
saw blade guard (2) (see 6.4, 6.6, 6.7)
- 31 -
28.06.2021 11:11:06