Before Starting The Equipment - Kraftixx TKS 254/2000 Manual De Instrucciones Original

Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the level
specifi ed during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Anl_TKS_254-2000_SPK7.indb 30
GB
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
Unpack the bench-type circular saw and
check it for damage which may have occurred
in transit.
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the saw blade to run
freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.
6. Assembly
Danger! Pull out the power plug before carry-
ing out any maintenance, resetting or assem-
bly work on the circular saw!
6.1 Assembling the base frame (Fig. 3-4)
Danger! Make allowance for the weight of the
machine and arrange another person to help you
if necessary!
•
Turn the bench-type circular over and set the
saw down on the floor or on some other work
surface. Important! Place suitable material
(e.g. packaging material) between the table
surface and the surface on which it is stood to
prevent any damage to the table surface.
•
Important! Only fasten all the screw connec-
tions between the base frame and machine
loosely at first. Wait until you have returned
the bench-type circular saw to its working po-
sition before tightening the screw connections
securely. This is so that you can be sure the
base frame is aligned level with the surface
on which it is stood.
•
Use the hexagon screws (46) to fasten the
four legs (29) loosely to the bench-type circu-
lar saw.
•
Then use the lock bolt (48), washer (49),
spring washer (50) and nuts (51) to screw the
cross-struts (30/31) loosely to the legs (29).
Make sure that the tongue-and-groove con-
nection between the cross-strut (30/31) and
- 30 -
28.06.2021 11:11:06