Behringer ULTRACURVE PRO DEQ2496 Guia De Inicio Rapido página 5

8
ULTRACURVE PRO DEQ2496
ULTRACURVE PRO DEQ2496 Controls
Step 2: Controls
(EN)
(1) (3) (6) (8)
(2) (5) (4) (7)
(1) The LED METER indicates the DEQ2496's input signal. The top CLIP LED lights
up as soon as the input signal level is too high or the peak limiter in the
Dynamics menu has been activated.
(2) Use the METER key to select the METER menu.
(3) The DEQ2496 features a built-in real-time analyzer displaying the entire
frequency range. Use the RTA key to select the corresponding menu and
adjust the various settings.
(4) Depending on the currently selected menu, the COMPARE key allows you to
compare either complete presets or individual modules. The following table
shows how the COMPARE key works in each module.
COMPARE COMPARE
(complete preset) (module only)
GEQ x
PEQ x
x
DEQ
x
FBD
WIDTH x
x
DYN
x
UTIL
I/O x
BYPASS x
not active
RTA
MEMORY x
METER not active
(9) (10) (11)
(5) Press the MEMORY key to select the MEMORY menu. Here, you can save or
recall complete presets or individual modules from one preset (e.g. GEQ,
PEQ etc.). The MEMORY LED lights up as soon as the parameter values of the
preset selected in the MEMORY menu differ from currently active settings.
(6) The PAGE key allows you to select the various pages within one menu.
(7) The functions performed by the keys A and B depend on the selected menu
and are indicated in the display.
(8) This is the LC display of your ULTRACURVE PRO
(9) The DEQ2496 has three DATA WHEELS, which can be used to select and edit
various parameters—again depending on the currently selected menu.
Often, they perform a dual function, i.e. you can edit by turning and pressing
a data wheel. Pressing the data wheels also changes the scaling of many
parameters (step width) or confirms/resets previously made entries.
(10) With the menu keys you can select the individual menus of the various
modules. They can also be used to select specific pages from these menus
(like PAGE key). Each of these keys has a built-in LED, which lights up when
the corresponding module starts modifying the sound. When the DEQ2496
receives MIDI data, the LED of the UTILITY key lights up briefly. Keep this key
pressed for about 1 s to bypass active modules or re-activate disabled ones.
This function refers only to those modules which can be edited in the
BYPASS menu.
(11) Use the POWER switch to put the DEQ2496 into operation. This switch
should be set to "Off" before you connect the unit to the mains.
9
Quick Start Guide
(12) (13) (14) (15) (16)
(12) The FUSE HOLDER holds the mains fuse of the DEQ2496. Blown fuses must
be replaced by fuses of the same type and rating.
(13) The mains connection is made using the enclosed power cord and a
standard IEC receptacle.
(14) The MIDI jacks enable the DEQ2496 to communicate with a computer or
other MIDI equipment. Incoming MIDI data are received on the MIDI IN,
outgoing MIDI data are sent via the MIDI OUT. Received MIDI data are also
present at the MIDI THRU jack, so as to pass them on unmodified to
other devices.
(15) Use the WORDCLOCK input to synchronize your DEQ2496 to external
equipment via a wordclock signal. This connector is on a BNC coaxial jack.
(16) Your DEQ2496 features a digital optical interface for the transmission/
reception of data in both AES/EBU and S/PDIF formats.
(17) The digital AES/EBU interface (XLR connectors) also sends/receives
AES/EBU or S/PDIF signals.
(17) (18) (19) (20) (21) (22)
(18) The AUX OUT phone jack is an additional stereo output, which allows you
to tap the audio signal present at the digital outputs in analog form.
(19) The RTA/MIC IN XLR connector can be used to connect a measurement
microphone providing an input signal for the real-time analyzer or
SPL meter. This connector has a switchable +15 V phantom power supply
for condenser microphones and can be set to microphone or line sensitivity.
(20) The MAX switch raises the maximum level present at the MAIN inputs/
outputs from +12 dBu to +22 dBu.
(21) These balanced XLR connectors provide the analog output signal
of the DEQ2496.
(22) These balanced XLR inputs are used to connect analog input signals.