Functional Description - Makita LM001C Manual De Instrucciones

FUNCTIONAL
DESCRIPTION
Installing or removing portable
power pack
CAUTION:
Always switch off the machine before
installing or removing the portable power pack.
CAUTION:
Hold the machine and the portable
power pack firmly when installing or removing porta-
ble power pack. Failure to hold them firmly may cause
them to slip off your hands and result in damage to the
machine and portable power pack and a personal injury.
CAUTION:
Make sure that the portable power
pack is securely installed to the machine. If not,
it may accidentally fall out of the machine, causing
injury to you or someone around you.
CAUTION:
Before operation, make sure that
the cord is securely attached to the cord holders
and the socket is inserted into the plug all the way.
For PDC1200
1.
Place the cord of the portable power pack as
shown in the figure.
► Fig.16: 1. Portable power pack 2. Cord
2. Install the portable power pack to the machine as
shown in the figure.
► Fig.17: 1. Battery support lever 2. Portable power
pack 3. Lock button
CAUTION:
Make sure that the portable power
pack is securely locked to the battery support
levers and the lock button is securely locked.
3. Attach the cord to the cord holders as shown in
the figure. Open the plug cover, then align the arrow
mark on the socket with that on the machine, and then
insert the socket into the plug all the way.
► Fig.18: 1. Plug cover 2. Arrow mark 3. Socket
4. Cord
NOTICE:
Do not insert the socket forcibly. If
the socket cannot be inserted easily, it is not being
inserted correctly.
NOTICE:
When disconnecting the socket from
the plug, do not hold the cord but hold the socket.
Otherwise, the cord may be damaged and cause a
malfunction of the machine.
4. Open the lock key cover, then insert the lock key
in the place shown in the figure as far as it will go, and
then close the lock key cover.
► Fig.19: 1. Lock key 2. Lock key cover
To remove the portable power pack, perform the instal-
lation procedure in reverse.
For PDC01
NOTE: Before installing the portable power pack to
the machine, install at least one battery to battery port
1 or 2, and at least one battery to battery port 3 or 4.
1. Place the cord of the portable power pack as
shown in the figure.
► Fig.20: 1. Portable power pack 2. Cord
2.
Install the portable power pack to the machine
as shown in the figure. Lock the locking levers on both
sides of the portable power pack.
► Fig.21: 1. Battery support lever 2. Locking lever
3. Portable power pack
CAUTION:
Make sure that the portable power
pack is securely locked to the battery support
levers and the locking levers are securely locked.
3.
Attach the cord to the cord holders as shown in
the figure. Open the plug cover, then align the arrow
mark on the socket with that on the machine, and then
insert the socket into the plug all the way.
► Fig.22: 1. Plug cover 2. Arrow mark 3. Socket
4. Cord
NOTICE:
Do not insert the socket forcibly. If
the socket cannot be inserted easily, it is not being
inserted correctly.
NOTICE:
When disconnecting the socket from
the plug, do not hold the cord but hold the socket.
Otherwise, the cord may be damaged and cause a
malfunction of the machine.
4. Open the lock key cover, then insert the lock key
in the place shown in the figure as far as it will go, and
then close the lock key cover.
► Fig.23: 1. Lock key 2. Lock key cover
To remove the portable power pack, perform the instal-
lation procedure in reverse.
Machine / battery protection system
The machine is equipped with a machine/battery
protection system. This system automatically cuts off
power to the motor to extend machine and battery life.
The machine will automatically stop during operation if
the machine or battery is placed under one of the fol-
lowing conditions:
Overload protection
When the battery is operated in a manner that causes
it to draw an abnormally high current, the machine
automatically stops and the main power lamp blinks in
green. In this situation, turn the machine off and stop
the application that caused the machine to become
overloaded. Then turn the machine on to restart.
Overheat protection
When the machine or battery is overheated, the
machine stops automatically and the main power lamp
lights up in red. In this case, let the machine and battery
cool before turning the machine on again.
15 ENGLISH