Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 17

Enlaces rápidos

SERIES 99H–EU HORIZONTAL AIR GRINDERS
Series 99H–EU Grinders are designed for heavy duty metal removal in foundry work
and similar applications.
Ingersoll–Rand is not responsible for customer modification of tools for applications on
which Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state, federal
and country), that may apply to hand held/hand
operated pneumatic tools.
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the inlet
with 3/4" (19 mm) inside diameter air supply hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
label.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 2000
Printed in U.S.A.
INSTRUCTIONS FOR
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating
this tool.
Keep hands, loose clothing and long hair away from
rotating end of tool.
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended air
pressure.
Tool accessories may continue to rotate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using any
tool if discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
Use accessories recommended by Ingersoll–Rand.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
03530367
Form P6502–EU
Edition 8
August, 2000
GB
Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 99H–EU Serie

  • Página 17: Instrucciones Para Amoladoras Neumáticas Horizontales De La Serie 99H-Eu

    03530367 Impreso P6502–EU Edición 9 Agosto, 2000 INSTRUCCIONES PARA AMOLADORAS NEUMÁTICAS HORIZONTALES DE LA SERIE 99H–EU NOTA Las amoladoras de la serie 99H–EU están diseñadas para eliminación de metal en trabajos de fundición de servicio pesado y aplicaciones similares. Ingersoll–Rand no aceptará responsabilidad alguna por la modificación de las herramientas efectuada por el cliente para las aplicaciones que no hayan sido consultadas con Ingersoll–Rand.
  • Página 18: Etiquetas De Aviso

    ETIQUETAS DE AVISO AVISO EL HACER CASO OMISO DE LOS AVISOS SIGUIENTES PODRÍA OCASIONAR LESIONES. ADVERTENCIA ADVERTENCIA ADVERTENCIA Cortar siempre el suministro Usar siempre protección ocular Usar siempre protección de aire y desconectar la man- al manejar o realizar opera- para los oídos al manejar guera de suministro de aire ciones de mantenimiento en...
  • Página 19: Para Poner La Herramienta En Servicio

    AVISOS ESPECÍFICOS SOBRE LA AMOLADORA AVISO: Combinaciones incorrectas de rueda de rectificación, protector de rueda y velocidad de herramienta puedan resultar en lesionamientos. Las combinaciones correctas se especifican a continuación: Número de Pieza del Tipo de Rueda Diámetro de Rueda Grosor Máximo de Velocidad Máxima Protector...
  • Página 20: Declaración De Conformidad

    DECLARACIÓN DE CONFORMIDAD Ingersoll–Rand, Co. os abajo firmantes (nombre del proveedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (domicilio) declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Amoladoras neumáticas horizontales de la serie 99H–EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE ISO8662, PNEUROP PN8NTC1...
  • Página 25 Service Centers Centres d’entretien Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll–Rand Company Ingersoll–Rand Nederland Produktieweg 10 510 Hester Drive 2382 PB Zoeterwoude White House Nederland TN 37188 Tel: (31) 71 452200 Fax: (31) 71 5218671 Tel: (615) 672 0321 Fax: (615) 672 0801 Ingersoll–Rand Company SA PO Box 3720...

Tabla de contenido