Tabla de contenido
Idiomas disponibles
Idiomas disponibles
EngLIsh
Screw the side handle
tightly into one of the holes on either
5
side of the gear case.
Mounting and Removing the Cutting Shroud
Mounting the DWE46225 125 mm Cutting Shroud
(Fig. A, C, D)
WARNING: It is not possible to use the cut-off tool with a
with a protective guard for grinding applications.
1. Press the front shroud button
shroud button
15
at the same time to fully open the
cutting shroud (Fig. D).
2. Loosen the collar screw
9
the tabs
22
on the cutting shroud with the slots
cut-off tool gear case.
3. Rotate the shroud into the desired working position. The
shroud should be positioned between the spindle and the
operator to provide optimum efficiency.
4. Tighten the collar screw
9
the gear case. Do not operate the cut-off tool with a loose
cutting shroud.
5. To remove the cutting shroud, loosen the collar screw,
rotate the cutting shroud to align the slots and tabs and pull
up on the cutting shroud.
nOTE: The cutting shroud is pre-adjusted to the diameter of the
gear case hub at the factory. If, after a period of time, the cutting
shroud becomes loose, tighten the collar screw
NOTICE: If cutting shroud cannot be secured by
tightening the collar screw, do not use tool. Take the tool
and cutting shroud to a service centre to repair or replace
the cutting shroud.
Mounting and Using Diamond Cutting
Wheels (Fig. A, D, E)
WARNING: Only diamond wheels with a negative
rake angle shall be used with cutting shroud. Do not
cut metal. Do not use with bonded abrasive wheels.
1. With the cutting shroud attached to the cut-off tool, press
the front shroud button
14
at the same time to fully open the cutting shroud.
2. Install the backing flange,
18
3. Place the wheel
26
on the locking flange
both on the spindle, against the backing flange, centering
the wheel on the raised center of the backing flange.
4. While depressing the spindle lock button, tighten the
locking flange:
Tighten standard locking flange using a wrench.
-
5. After the diamond cutting wheel is mounted, the cutting
shroud must be closed by pressing the front shroud
button
14
and the side shroud button
same time.
6. To remove the wheel, depress the spindle lock button and
loosen the locking flange.
Depth of Cut Adjustment (Fig. A)
1. Loosen the depth of cut adjustment knob
38
14
and the side
on the cutting shroud and align
23
on the
to secure the cutting shroud on
9
.
and the side shroud button
15
, on spindle
4
.
19
, and place
15
at the
12
.
2. Slide the depth of cut adjustor
note: If the shroud is closed, press the front shroud
button
14
to open the shroud. This will make it easier to
move the depth of cut adjustor.
3. Tighten the depth of cut adjustment knob.
Dust Extraction (Fig. A, F)
WARNING: Use only power tools recommended by
D
WALT with this attachment.
e
For more information about D
with this attachment, please contact one of the authorized
services centers listed on the back cover or refer to the full
details of our after-sales service available on the Internet at:
www.2helpU.com.
WARNING: This attachment must be used with a dust
extractor system. ALWAYS wear certified safety face or
dust mask.
nOTE: Ensure hose connection is secure.
nOTE: The amount of dust retained by the dust extractor
vacuum is dependent on its filter system. Refer to the dust
extractor vacuum instruction manual for more information.
All D
WALT dust collection shrouds are designed to work with
e
the D
WALT Airlock DWV9000 connector.
e
1. Attach the DWV9000 connector
hose
25
.
2. Unlock the DWV9000 connector
port
.
8
3. Lock the DWV9000 connector
Traditional Dust Extractor Vacuum Hoses
Attach recommended dust extractor vacuum hose to dust
port
8
.
Removing and Attaching Wheels (Fig. G)
This cutting shroud comes with four removable wheels
the metal base
which can be detached if not needed.
10
1. Remove the clips
27
holding the wheels to the base.
2. Remove the wheels.
3. Remove the pivot pin
.
28
To attach the wheels to the base, reinsert the pivot pin, slide
the wheels on their axles and secure the clips in place. Make
sure all four wheels are securely attached before using the
cutting shroud.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
to the desired position.
11
WALT power tools compatible
e
24
to your dust collector
24
and slide onto dust
24
to secure.
13
on
Tabla de contenido
