Bluetooth Audio; Sleep Function; Clock Setup - Lenco KCR-100 Manual De Usuario

Recall Stored FM Presets
Press the MEMORY button on the unit (or the CH-/CH+ button on the remote control) to tune to different preset channel.
To directly recall the preset channel by using the numeric buttons on the unit, press the numeric buttons [1], [2], ..., [5].
For example when the button [3] is pressed, the display shows "P03" and wait for a while it will tune to the preset 3.
Or when press and hold the button [3/(8)] button until the display shows "P08" and wait for a while, it will tune to the preset 8.
Or when press the button [1] button and followed by pressing the button [2], the display will show "P12" and after a while it will tune
to the preset 12.
Or when press the button [1] button and followed by press and hold the button [3/(8)], the display will show "P18" and after a while
it will tune to the preset 18.
Alternatively you can use the remote control numeric buttons to directly recall the preset channel, press the numeric buttons [1],
[2], ..., [9], [0].
For example when the button [3] is pressed, the display shows "P03" and wait for a while it will tune to the preset 3.
Or when press the button [8] until the display shows "P08" and wait for a while, it will tune to the preset 8.
Or when press the button [1] and followed by pressing the button [2], the display will show "P12" and after a while it will tune to the
preset 12.
Or when press the button [1] and followed by press the button [8], the display will show "P18" and after a while it will tune to the
preset 18.
Stereo/Force Mono Selection
When receiving a Stereo FM radio channel, press the ST/MONO button will switch between stereo audio and force mono audio.
When it is in FM Stereo, the FM-ST LED will be turned on.
Note:
- The antenna wire at the rear panel of the unit should be fully extended to ensure a good FM reception. Alter the antenna
position for the best reception.

BLUETOOTH AUDIO

Please follow the pairing instructions below to link the unit to your Bluetooth device.
1. Press the SOURCE button to enter the Bluetooth mode. The display will show "bLUE". It will start searching and the BT LED will
flash.
2. If the unit has never been paired with a Bluetooth device before or cannot find the last paired device, the BT LED will keep on
flashing. Turn on the Bluetooth function of your device and enable the search until "Lenco KCR-100" is found. Select "Lenco KCR-
100" on the Bluetooth device to make connection. Enter the pass code "0000" if required.
3. After successfully paired the BT LED will become steady without flashing.
4. You can now start playing music from your smartphone wirelessly to the speaker.
5. You can press the PLAY/PAUSE
6. You can press the PREVIOUS
• Press and hold the PAIRING button will disconnect the current connection and start to search another new Bluetooth device.

SLEEP FUNCTION

1. When the unit is switched on, press the SLEEP button on the remote control repeatedly to select the sleep duration in minutes
from 05, 10, 15, 30, 45, 90 and 00 (sleep off).
2. When the sleep timer is zero, the unit will be turned off automatically.
3. To cancel the sleep function, press and hold the STANDBY button on the unit (or press the STANDBY button on the remote
control) to turn off. Alternatively press the SLEEP button repeatedly to "00".

CLOCK SETUP

1. Turn off the unit in Standby mode.
2. Press and hold the CLOCK SET button on the unit (or press the CLOCK SET button on the remote control) to enter the Clock setup.
"24H" or "12H" will be displayed.
3. Press the MIN. and SEC button on the unit (the MIN. and SEC. button on the remote control) to toggle between 24H (display 24
hours format) or 12H (display 12 hours format). Press the CLOCK SET button on the unit (the CLOCK SET button on the remote
control) to confirm.
4. Press the MIN. and SEC button on the unit (the MIN. and SEC. button on the remote control) to adjust the hour and minute
respectively. Press the CLOCK SET button on the unit (the CLOCK SET button on the remote control) to finish the clock set.
button to pause or resume the playback.
or button to skip to the previous or next song.
10