Tabla de contenido
Idiomas disponibles
Idiomas disponibles
subject to variation based on product components, temperature
and end-user application.
Assembling the Guard (Fig. D, E)
WARNING:
or personal injury could result.
WARNING:
WITHOUT GUARD FIRMLY IN PLACE. The guard must
always be properly attached on the appliance to protect
the user.
1. Assemble the guard
8
2. Using a crosshead screwdriver, insert the 4 guard screws and
tighten securely.
An extended coverage guard is available (sold separately) for
extra coverage if desired. Use STANLEY FATMAX replacement
guard.
Assembling the Pole (Fig. C–E)
1. Do not remove the zip tie until the pole is assembled.
2. Ensure that the sleeve
pole
is fully extended.
6
nOTE: To adjust the sleeve, release the sleeve latch
move the sleeve into position.
3. Lock the sleeve latch.
4. With the sleeve latch closed, slide the upper trimmer pole
into the sleeve lower trimmer pole. The latching button
will click into position when it engages the latch hole.
5. Tighten the top screw
Attaching the Auxiliary Handle (Fig. F)
1. Place the auxiliary handle
trimmer pole
as shown in Figure F.
6
2. Slide the bracket
of the auxiliary handle onto the
31
bottom of the handle.
3. Thread the handle bolts
the bracket from above.
4. Tighten the handle bolts. Ensure the handle is securely
attached by closing the handle clamp
5. To adjust the position of the auxiliary handle, open the
handle clamp and slide the handle up and down the pole
until it is in the desired location. Close the clamp to lock the
handle in place.
Height Adjustment (Fig. E)
CAUTION:
obtain proper working positions.
1. The overall height of the trimmer can be adjusted by
loosening the height-adjust collar
direction of the arrow shown in Figure E.
Never remove the guard. Damage
NEVER OPERATE APPLIANCE
to the motor housing
.
5
on the lower trimmer
14
15
with a crosshead screwdriver.
18
onto the top of the upper
4
through the handle and into
32
.
19
Adjust the length of the trimmer to
by rotating it in the
6
2. Move the upper housing straight up or down. When the
desired height is achieved, tighten the collar by rotating it
opposite of the direction shown in Figure E.
Releasing the Cutting Line (Fig. A)
In transit, the cutting line is taped to the spool housing
•
Remove the tape holding the cutting line to the
spool housing.
OPERATION
Instructions for Use
WARNING:
instructions and applicable regulations.
WARNING:
personal injury, turn tool off and disconnect battery
pack before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. A, I)
WARNING:
and
personal injury, ALWAYS use proper hand position
as shown.
WARNING:
17
personal injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
and one hand on the auxiliary handle
13
Switching Trimmer On and Off (Fig. A)
To turn the appliance on, squeeze the lock-off lever
the variable speed trigger
release the lock off lever. To turn the appliance off, release the
variable speed trigger.
WARNING:
in the on position.
Speed Control Switch (Fig. A)
This string trimmer gives you the choice to operate at a
more efficient speed to extend the runtime for larger jobs, or
accelerate the trimmer speed for high- performance cutting.
To extend runtime, pull the speed control switch back toward
the battery housing
for larger projects that require more time to complete.
To accelerate the trimmer, push the speed control switch
forward toward the auxillary handle
This mode is best to cut through heavier growth and for
applications that need higher RPM.
nOTE: When in "HI" mode, runtime will be decreased as
compared to when trimmer is in "LO" mode.
Always observe the safety
To reduce the risk of serious
To reduce the risk of serious
To reduce the risk of serious
. Once the unit is running, you may
1
Never attempt to lock the trigger
into the "LO" position. This mode is best
10
into the "HI" position.
4
English
.
10
.
4
and then
2
3
11
Tabla de contenido
