Fiap Light Active Spot Manual Del Usuario página 3

FIAP Light Active Spot
GB
Information about this operating manual
Please read the operating instructions and familiarise yourself with the unit prior to using it for the first
time. Adhere to the safety information for the correct and safe use of the unit.
Intended use
The use of the FIAP Light Active Spot and FIAP Light Active Spot SET, in the following text termed
unit, is exclusively intended for fountain systems and ponds at a water temperature of between + 4 °C
and + 35 °C and up to an immersion depth of 4 meters, as well as for use out of the water. Ensure that
the power pack is only operated at ambient temperatures of – 10 °C to 40 °C.
Use other than that intended
Danger to persons can emanate from this unit if it is not used in accordance with the intended use and
in the case of misuse. If used for purposes other than that intended, our warranty and operating permit
will become null and void.
CE Manufacturer's Declaration
We declare conformity in the sense of the EC directive, EMC directive (89/336/EEC) as well as the low
voltage directive (73/23/EEC). The following harmonised standards apply:
EN 60598-2-7, EN 61558-1, EN 61558-2-6, EN 60825-1
Safety information
FIAP has manufactured this unit to the current state of the art and the valid safety regulations. Despite
of the above, hazards for persons and assets can emanate from this unit if it is used in an improper
manner or not in accordance with its intended use, or if the safety instructions are ignored.
For safety reasons, children and young persons under 16 years of age as well as persons who
cannot recognise possible danger or who are not familiar with these operating instructions, are
not permitted to use the unit!
Please keep these operating instructions in a safe place! Also hand over the operating instructions
when passing the unit on to a new owner. Ensure that all work with this unit is only carried out in
accordance with these instructions.
The combination of water and electricity can lead to danger to life and limb, if the unit is incorrectly
connected or misused.
Attention! Danger of electric shock. Ensure that the cable connection points and their
surroundings are dry.
Protect the connection cable when burying to avoid damage. Only use cables approved for outside
use. Ensure that the power connection cable cross section is not smaller than that of the rubber sheath
with the identification H05RN-F. Extension cables must meet DIN VDE 0620. Only use unwound
cables. Electrical installations in garden ponds and swimming ponds must meet the national and
international regulations valid for installers. Compare the electrical data of the supply with those on the
unit type plate. This data must coincide.
Never operate the unit if the cable or housing are defective! Disconnect the power! Do not carry or pull
the unit by the connection cable.
Attention! Install the safety transformer at a flood protected place and provide a minimum spacing of 2
m from the pond edge. Never open the unit housing or its attendant components, unless this is
explicitly mentioned in the operating instructions. Always disconnect the power supply of all units
located in water and of this unit prior to performing work on the unit! For your own safety, consult a
qualified electrician if you have questions or encounter problems!
Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045
FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen
Tel: 09628 9213 0; Fax: 09628 9213 30;
5
www.fiap.com
FIAP Light Active Spot
Set-up and start-up
When set up above the water level, maintain a safety distance of at least 50 cm from combustible
material. Ensure a safe seating. Do not cover the unit. Danger of fire! Position the unit such that it does
not present a hazard for anybody. When fitting in the pond, fasten the unit on a suitable base by
means of the swivel bracket. The ground stake can be used when installing the unit out of the water.
Connect the power plug of the spotlight to the socket of the transformer bush. Connect the transformer
to the power supply. Check the spotlight function.
Cleaning
Adhere to the safety instruction! Only use water and a soft brush. Ensure that no moisture can enter
the unit.
Disposal
Dispose of the unit in accordance with the national legal regulations.
Malfunctions
Malfunction
LED does not light up Power supply interrupted
Bulb contacts corroded
Light intensity decreases Lamp glass soiled
Water in the spotlight housing Seal defective
Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045
FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen
Tel: 09628 9213 0; Fax: 09628 9213 30;
Cause Remedy
Check power supply
Clean contacts
Clean
Check sealing rings and
replace, if necessary
www.fiap.com
6