Milwaukee M12 BD Manual Original página 8

TECHNICAL DATA CORDLESS SCREWDRIVER
Production code.......................................................................................................
Drilling capacity in steel ...........................................................................................
Drilling capacity in wood ..........................................................................................
Wood screws (without pre-drilling) ..........................................................................
No-load speed 1st gear ...........................................................................................
No-load speed 2nd gear ..........................................................................................
Torque max (Li-Ion Battery 2.0 Ah) * .......................................................................
Torque max (Li-Ion Battery 4.0 Ah) * .......................................................................
Battery voltage.........................................................................................................
Tool reception ..........................................................................................................
Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah...6,0 Ah) ......................
Recommended ambient operating temperature ......................................................
Recommended battery types...................................................................................
Recommended charger ...........................................................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ........................................................
Sound power level (Uncertainty K=3dB(A)) .............................................................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN
62841.
Vibration emission value a
h
Drilling into metal .................................................................................................
Uncertainty K= .....................................................................................................
Screwing ..............................................................................................................
Uncertainty K= .....................................................................................................
* Measured according to Milwaukee Standard N 877318
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to
compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent
accessories or poorly maintained, the vibration and noise emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is running but not actually
doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands
warm, organization of work patterns.
WARNING Read all safety warnings, instructions, illustrations and
specifi cations provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SCREWDRIVER SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when performing an
operation where the fastener may contact hidden wiring. Fasteners
contacting a "live" wire may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the
machine. The use of protective clothing is recommended, such as dust mask,
protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale
the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch the
device on again while the insertion tool is stalled, as doing so could trigger a
sudden recoil with a high reactive force. Determine why the insertion tool stalled
and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
14 ENGLISH
M12 BD
............................. 4419 01 05...
...000001-999999
...................................10 mm
...................................20 mm
.....................................6 mm
..............................0-400 min -1
............................0-1500 min -1
...................................30 Nm
...................................38 Nm
...................................12 V
................................ 1/4" (6,35 mm)
.................1,00 kg...1,26 kg
...........................-18°C ... +50 °C
................................. M12B...
M12-18 C; M12-18 FC; M12-18 AC; M12 C4; C12 C
................................85,0 dB (A)
................................96,0 dB (A)
..................................1,5 m/s 2
..................................1,5 m/s 2
..................................0,4 m/s 2
..................................1,5 m/s
2
• when setting the device down
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric cables and gas
or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can
cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning
them. Milwaukee Distributors off er to retrieve old batteries to protect our
environment.
Do not store the battery pack together with metal objects (short circuit risk).
Use only System M 12 chargers for charging System M 12 battery packs. Do not
use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep
dry at all times.
Battery acid may leak from damaged batteries under extreme load or extreme
temperatures. In case of contact with battery acid wash it off immediately with
soap and water. In case of eye contact rinse thoroughly for at least 10 minutes
and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage due to
a short circuit, never immerse your tool, battery pack or charger in fl uid or allow
a fl uid to fl ow inside them. Corrosive or conductive fl uids, such as seawater,
certain industrial chemicals, and bleach or bleach containing products, etc., can
cause a short circuit.
SPECIFIED CONDITIONS OF USE
The battery drill/screwdriver may be used for drilling and screwdriving for
independent use away from mains supply.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described under
"Technical Data" fulfi lls all the relevant regulations and the directives 2011/65/EU
(RoHS), 2014/30/EU, 2006/42/EC, and the following harmonized standards
have been used:
EN 62841-1:2015
EN 62841-2-2:2014
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-10-23
Alexander Krug
Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant provisions of the
following Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091 (as
amended), S.I. 2012/3032 (as amended) and that the following designated
standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-2:2014
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
Winnenden, 2020-10-23
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time should be recharged
before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery
pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged, after used.
To obtain the longest possible battery life remove the battery pack from the
charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from
moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations that cause
high current draw, the tool will vibrate for about 5 seconds, the fuel gauge will
fl ash,and then the tool will turn OFF. To reset, release the trigger.
Under extreme circumstances, the internal temperature of the battery pack could
raise too much. If this happens, the fuel gauge will fl ash until the battery pack
cooled down. After the lights go off , the work may continue.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
• The user can transport the batteries by road without further requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject to
Dangerous Goods regulations. Transport preparation and transport are
exclusively to be carried out by appropriately trained persons and the process
has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to prevent
short circuit.
• Ensure that battery pack is secured against movement within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and spare parts. Should components need to
be replaced which have not been described, please contact one of our
Milwaukee service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
machine type printed as well as the six-digit No. on the label and order the
drawing at your local service agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the
machine.
Please read the instructions carefully before starting the
machine.
Do not dispose electric tools, batteries/rechargeable batteries
together with household waste material.
Electric tools and batteries that have reached the end of their
life must be collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for recycling advice
and collection point.
n
No-load speed
0
V
Volts
Direct current
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 15