Bosch Professional GLI 18V-2200 C Manual Original página 12

12 | English
Assembly
Battery Charging (see figure B)
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". A protective circuit
switches the cordless worklight off when the battery is
drained.
Do not continue to press the on/off switch after the
u
worklight has been automatically switched off. This
can damage the battery. Ensure that the battery is
charged and that the cordless worklight has cooled down
before switching the cordless worklight on again.
To remove the battery (14), press the release button (13)
and pull the battery out of the cordless worklight. Do not use
force to do this.
Follow the instructions on correct disposal.
Putting the Button Cell into Operation
(see figure B)
Remove the separating film between the button cell (11)
and the button cell contact when using the tool for the first
time.
The cordless worklight is fitted with a button cell so that it
can be detected by the mobile device even if no battery (14)
is inserted.
Unlock the locking mechanism of the battery cover (2) and
fold up the battery cover (3).
Unscrew the screw of the battery compartment cover (9)
and remove the battery compartment cover (10).
Remove the film from the button cell contact and reattach
the battery compartment cover with the screw.
Operation
Start-up
Inserting the Battery
Unlock the locking mechanism of the battery cover (2) and
fold up the battery cover (3).
Insert the charged battery (14) into the lamp head (4) until
you feel it engage and it is flush with the lamp head (4).
Close the battery cover (3) and then the locking mechanism
of the battery cover (2).
Make sure that the rubber lip is seated correctly when
u
closing the battery cover. Otherwise protection against
dust and splash water will not be ensured.
Setting up
Carefully fold out the stand (5) and place the cordless work-
light on the floor. Make sure it is secure.
1 609 92A 6TX | (01.09.2021)
Fastening to the tripod
You can use the tripod mount (7) to screw the cordless
worklight onto a tripod.
Tighten the 5/8" screw. Ensure that the tripod has a firm
footing.
Swivelling the Lamp Head (see figure A)
The lamp head (4) is attached to the carrying handle (8).
The lamp head can be set to five different positions using the
carrying handle.
Switching On/Off
To start up the cordless worklight, press the on/off switch
(1).
To switch off the cordless worklight, press the on/off switch
(1) again.
Adjusting the Brightness
Press the on/off switch (1) briefly to switch on the cordless
worklight with maximum brightness. To adjust the bright-
ness in two stages, hold down the on/off switch (1) until the
required brightness is reached.
Temperature-dependent overload protection
When the permitted operating temperature is exceeded, the
cordless worklight initially reduces the brightness before
switching itself off if required for protection. Let the cordless
worklight cool down and then switch the cordless worklight
back on.
Changing the Button Cell (see figure B)
Make sure that the battery compartment (12) is not
u
damaged when removing the cell.
Make sure that the positive pole of the button cell
u
faces upwards.
A warning will be displayed in the app before the button
cell (11) is fully used up.
To change the button cell (11), unlock the locking mechan-
ism of the battery cover (2) and fold up the battery
cover (3).
Unscrew the screw of the battery compartment cover (9)
and remove the battery compartment cover (10).
Remove the empty button cell and insert a new button cell.
Reattach the battery compartment cover with the screw.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For reasons of safety, it is only
possible to query the state of charge when the cordless
worklight is switched off.
Press the button for the battery charge indicator
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
or to
Bosch Power Tools