Tabla de contenido
Idiomas disponibles
Idiomas disponibles
EngLIsh
7. Place a new belt over the pulleys
arrow on the inside of the belt points in the same direction
as the arrow
22
on the backing plate.
8. Release the lever.
9. Holding the threaded pin
23
backing plate.
10. Replace the cover and tighten the nut.
11. Replace the knob and tighten it.
WARNING: When mounting a leather honing belt, make
sure that the leather surface is on the outside.
Adjusting the Grinding or Honing Belt
(Fig. E)
Centering the Belt
If the belt
5
is not properly centered, adjust by turning the
centering knob
.
8
Adjusting the Belt to the Workpiece
The belt can be adjusted to suit workpieces with concave,
convex or straight cutting edges.
1. Slacken the knob
9
.
2. Set the backing plate
to the appropriate position (up,
19
flush or down).
3. Tighten the knob
9
.
Preparing the Honing Belt for Use
Leather honing belts must be dressed before first use and when
the honing effect decreases.
With the machine switched off, spread a thin and even coating
of honing paste over the entire outside surface of the belt.
Mounting the Spark Guard (Fig. F, G)
The spark guard offers additional protection from sparks and
must be used whenever possible.
1. Fit the transparent screen
24
inserting a mushroom head bolt
guard and placing a washer
(Fig. F). Tighten the nut.
2. Hold the spark guard against the edge on top of the wheel
case
28
as shown (Fig. G).
3. Insert a mushroom head bolt
wheel case.
4. Place a washer
30
and nut
the nut hand-tight.
5. Position the guard at a distance of approx. 2 mm from the
wheel by sliding it towards the wheel.
6. Securely tighten the nut (torque: 6 Nm).
Adjusting the Workpiece Support (Fig. H)
The workpiece support can be set according to the workpiece
and the desired grinding angle.
1. Slacken the nut holding the support
2. Set the support to the desired position and angle, making
sure that the support is as close to the wheel as possible.
3. Tighten the nut (torque: 6 Nm).
24
, making sure that the
21
in its place, replace the
to the spark guard
by
6
25
into the screen and the
26
and nut
27
onto the bolt
29
into the guard and the
31
onto the bolt and tighten
3
.
Mounting and Adjusting the Clamping and
Grinding Attachment (Fig. A, I)
The clamping and grinding attachment is used to hold the
workpiece to the grinding wheel at a fixed angle.
1. Remove the fasteners holding the workpiece support
the bracket
4
and remove the workpiece support (Fig. A).
2. Mount the grinding attachment bracket
on the machine as shown using the hexagonal head
4
bolt
and corresponding nut
33
the grinding attachment bracket is at a distance of approx.
2 mm from the grinding wheel.
3. Insert the rod
of the grinding attachment into the forks
35
on the grinding attachment bracket as shown.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Proper Hand Position (Fig. L)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Refer to Figure L for proper body stance and hand positioning
when grinding and honing.
Switching On and Off (Fig. A)
To turn the tool on, set the on/off switch
To turn the tool off, set the on/off switch
Using the Grinding Wheel (Fig. A)
In order to achieve a straight cutting edge, move it slowly
backwards and forwards over the grinding wheel
a light pressure.
Using the Clamping and Grinding
Attachment (Fig. J)
1. Insert the workpiece into the clamping bracket
2. Position the workpiece as required to obtain the correct
bevel angle. The angle is a function of the protruding length
X (see Figure). For plane irons, X should be approx. 20 mm,
for chisels approx. 25–28 mm.
3. Tighten the star knobs
37
3
32
to the bracket
(Fig. I). Make sure that
34
1
to position 1.
to position 0.
1
. Only exert
2
36
.
.
to
Tabla de contenido
