Ingersoll Rand 7L–EU Serie Instrucciones

Ingersoll Rand 7L–EU Serie Instrucciones

Taladros angulares
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 17

Enlaces rápidos

TPD1401
Series 7L–EU Angle Drills are designed for drilling operations in the aerospace, automotive,
appliance, electronic, machining and furniture industries.
Ingersoll–Rand is not responsible for customer modification of tools for applications on
which Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state, federal
and country), that may apply to hand held/hand
operated pneumatic tools.
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the inlet
with 3/8" (10 mm) inside diameter air supply hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
label.
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 2000
Printed in U.S.A.
INSTRUCTIONS FOR
SERIES 7L–EU ANGLE DRILLS
03531415
Always wear hearing protection when operating
this tool.
Keep hands, loose clothing and long hair away from
rotating end of tool.
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended air
pressure.
Tool accessories may continue to rotate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using any
tool if discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
Use accessories recommended by Ingersoll–Rand.
Whenever the Angle Head is installed or
repositioned, the Throttle Lever must be positioned
so that reaction torque will not tend to retain the
throttle in the "ON" position.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
Form P6563–EU
GB
Edition 10
August, 2000
Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 7L–EU Serie

  • Página 17: Instrucciones Para Taladros Angulares De La Serie 7L-Eu

    03531415 Impreso P6563–EU Edición 10 TPD1401 Agosto, 2000 INSTRUCCIONES PARA TALADROS ANGULARES DE LA SERIE 7L–EU NOTA Los taladros angulares de la serie 7L–EU están diseñados para operaciones de taladrado en las industrias aeroespacial, del automóvil, de electrodomésticos, electrónica, mecánica y del mueble. Ingersoll–Rand no aceptará...
  • Página 18: Etiquetas De Aviso

    ETIQUETAS DE AVISO AVISO EL HACER CASO OMISO DE LOS AVISOS SIGUIENTES PODRÍA OCASIONAR LESIONES. ADVERTENCIA ADVERTENCIA ADVERTENCIA Cortar siempre el suministro de aire y desconectar la man- Use siempre protección ocular Use siempre protección para guera de suministro de aire cuando utilice esta herramienta los oídos cuando utilice esta antes de instalar, retirar o ajus-...
  • Página 19: Especificaciones

    PARA PONER LA HERRAMIENTA EN SERVICIO ESPECIFICACIONES ♦Nivel de GNivel de ruido Modelo Velocidad Par de calado Roscado hembra en vacío dB (A) vibraciones pulg.–lb Husillo Presión Potencia 7LH1A1–EU 6.000 1/4–28 – – – – – – – – – 7LJ1A1–EU 4.800 1/4–28...
  • Página 20: Declaración De Conformidad

    DECLARACIÓN DE CONFORMIDAD Ingersoll–Rand, Co. os abajo firmantes (nombre del proveedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (domicilio) declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Taladros Angulares de la Serie 7L–EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE EN292 IS08662...
  • Página 25 Service Centers Centres d’entretien Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll–Rand Company Ingersoll–Rand Nederland 510 Hester Drive Produktieweg 10 White House, TN 37188 2382 PB Zoeterwoude U.S.A. Nederland Tel: (615) 672 0321 Tel: (31) 71 452200 Fax: (615) 672 0801 Fax: (31) 71 218671 Ingersoll–Rand Company SA Ingersoll–Rand Sales Company Limited...
  • Página 26 NOTES...
  • Página 27 NOTES...
  • Página 48 Servicentre Servicecenter Servicesenter Huoltokeskus Centro de Serviço Ingersoll–Rand Company Ingersoll–Rand Nederland 510 Hester Drive Produktieweg 10 White House, TN 37188 2382 PB Zoeterwoude U.S.A. Nederland Tel: (615) 672 0321 Tel: (31) 71 452200 Fax: (615) 672 0801 Fax: (31) 71 218671 Ingersoll–Rand Company SA Ingersoll–Rand Sales Company Limited PO Box 3720...
  • Página 49 NOTES...
  • Página 50 NOTES...

Tabla de contenido