Standard Accessories; Optional Accessories; Practical Applications - Hitachi C 10FCH2 Instrucciones De Manejo

English

STANDARD ACCESSORIES

(1) 255 mm TCT Saw blade (mounted on tool) ................1
(2) Dust bag ......................................................................1
(3) 10 mm Box wrench .....................................................1
(4) Vise Assembly ............................................................1
(5) 4 mm Hex.bar wrench (only C10FCH2) ......................1
(6) Sub Fence (B) ............................................................1
(7) Flat screw ....................................................................1
(8) M6 Nylon nut ...............................................................1
(9) Plate (A) ......................................................................1
(10) Holder (B) ....................................................................1
(11) Side handle .................................................................1
Standard accessories are subject to change without notice.

OPTIONAL ACCESSORIES

(SOLD SEPARATELY)
(1) Extension Holder and Stopper
(2) Crown molding Vise Ass'y (Include Crown molding
Stopper (L))
(3) Crown molding Stopper (L)
(4) Crown molding Stopper (R)
Optional accessories are subject to change without notice.
APPLICATION
○ Cutting various types of aluminium sash and wood.
UNPACKING
○ Carefully unpack the power tool and all related items
(standard accessories).
○ Check carefully to make certain all related items
(standard accessories) are present.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the trigger
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. When the power tool is prepared for shipping, its
main parts are secured by a locking pin
Move the handle slightly so that the locking pin can be
disengaged.
During transport, lock the locking pin into the gear case
(Fig. 3).
5. Attach the dust bag to the main unit (Fig. 1)
(1) When the dust bag has become full of sawdust, dust
will be blown out of the dust bag when the saw blade
rotates.
Check the dust bag periodically and empty it before it
becomes full.
(2) During bevel and compound cutting, attach the dust
bag at a right angle to the base surface as shown in
Fig. 4.
10
CAUTION
Empty the dust bag frequently to prevent the duct and
the safety cover from becoming clogged.
Sawdust will accumulate more quickly than normal
during bevel cutting.
6. Installation
Ensure that the machine is always fi xed to bench.
Attach the power tool to a level, horizontal work bench.
Select 8 mm diameter bolts suitable in length for the
thickness of the work bench.
Bolt length should be at least 35 mm plus the thickness
of the work bench.
For example, use 8 mm × 60 mm bolts for a 25 mm thick
work bench.
ADJUSTING THE POWER TOOL PRIOR TO USE
CAUTION
Make all necessary adjustments before inserting the
plug in the power source.
1. Check to see that the lower guard operates
smoothly

PRACTICAL APPLICATIONS

WARNING
○ To avoid personal injury, never remove or place a
workpiece on the table while the tool is being operated.
○ Never place your limbs inside of the line next to warning
sign while the tool is being operated. This may cause
hazardous conditions (see Fig. 5).
CAUTION
○ It is dangerous to remove or install the workpiece while
the saw blade is turning.
○ When sawing, clean off the shavings from the turntable.
○ If the shavings accumulate too much, the saw blade
from the cutting material will be exposed. Never subject
your hand or anything else to go near the exposed
blade.
1. Tightly secure the material by vise assembly to be
cut so that it does not move during cutting
2. Switch operation
Pulling the trigger turns the switch on. Releasing the
trigger turns the switch off .
3. Holder (B), clamp lever adjustment (Fig. 6)
Attach the included holder (B) in the position as shown
in Fig. 6 and adjust the holder (B) until its bottom surface
contacts the work bench surface. After adjustments,
securely tighten the 6mm bolt with the included 10mm
box wrench. Loosen the M6 × 20 screw on the clamp
lever and attach to a position where the clamp lever can
be easily operated.
4. Using the Vise Assembly (Standard accessory)
(Fig. 7)
(1) The vise assembly can be mounted on either the left
fence {Fence (B)} or the right fence {Fence (A)} by
loosening the 6 mm wing bolt (A).
(2) The screw holder can be raised or lowered according to
the height of the workpiece by loosening the 6 mm wing
bolt (B). After the adjustment, fi rmly tighten the 6 mm
wing bolt (B) and fi x the screw holder.
(3) Turn the upper knob and securely fi x the workpiece in
position.
WARNING
Always fi rmly clamp or vise to secure the workpiece to
the fence; otherwise the workpiece might be thrust from
the table and cause bodily harm.