Handle Installation And Removal - Sears Kenmore 106.5004 Serie Manual De Uso Y Cuidado

6. Use a 3/8" nut driver to turn the leveling screws located in both
sides of the refrigerator. See graphic 10. Depending on uneven
floor conditions, you must turn one or both screws to the right
or left several times to raise or lower the refrigerator. Use a
bubble level if necessary until the refrigerator is steady.
7. Close both doors and check that they close as easily as you
like. If not, turn both screws to the right to raise the refrigerator
by tiling it more to the back until the doors close as easily as
you like.
8. Check and make sure that the technician sheet is placed in
the base grille cavity before assembling the base grille into
the cabinet.
9. Reinstall the base grille into the cabinet, first the left side of
the base grille and then the right side. See graphic 3. You may
insert the water dispenser tubing and wiring into base grille
cavity below the left bottom hinge.
10. Attach the base grille by pushing it by into the cabinet clips.
See graphic 2.
Door Alignment
The refrigerator doors are designed to be slightly misaligned
vertically when the refrigerator is empty. Please follow the next
steps to align the refrigerator doors.
1. Use an 11/16" open-ended wrench tool to loosen the locking
nut located below the refrigerator door. See graphic 11.
Accommodate the wrench tool so that it fits in the space.
2. Use a 5/16" open-ended wrench tool to turn the alignment
screw. See picture 12. Depending on how the refrigerator door
is misaligned in relation to the freezer door, you must turn the
screw to the right to raise or to the left to lower the refrigerator
door until both doors have been aligned vertically.
3. Tighten the 11/16" locking nut with the 11/16" wrench tool.
4. Reattach the base grille if it was dislodged.

HANDLE INSTALLATION AND REMOVAL

PARTS INCLUDED: Door handles (2), 1/8" hex key, spare
setscrew(s)
To Install the Handles:
NOTE: The handle mounting setscrews are preinstalled in the
handle.
1. Remove the handles, which are packed inside the refrigerator.
NOTE: To avoid scratching the finish, place the handles on a
towel or other soft surface.
2. Open the freezer door. On the refrigerator door, place the
handle on the shoulder screws with the setscrews facing
the freezer.
A
A. Shoulder screws
B. Setscrews inside the handle
8
3. Firmly push the handle toward the door until the handle base
is flush against the door.
4. While holding the handle, insert the short end of the hex key
into the upper hole and slightly rotate the hex key until it is
engaged in the setscrew.
5. Using a clockwise motion, tighten the setscrew until it begins to
contact the shoulder screw.
6. Repeat steps 4 and 5 to begin fastening the lower setscrew.
7. Once both setscrews have been partially tightened as outlined
in the previous steps, fully tighten both the upper and lower
setscrews.
IMPORTANT: When the screws feel tight, tighten them an
additional quarter-turn. The handle is not properly installed
without this extra tightening.
8. Open the refrigerator door and close the freezer door. Repeat
steps 2 through 7 to install the other handle onto the freezer
door with the setscrews facing the refrigerator.
9. Save the hex key and all instructions.
To Remove the Handles:
1. While holding the handle, insert the short end of the hex key
into the lower setscrew hole and slightly rotate the hex key until
it is engaged in the setscrew.
2. Using a counterclockwise motion, loosen the setscrew a quarter
turn at a time.
3. Repeat steps 1 and 2 for the upper setscrew. Gently pull the
handle away from the door.
4. If necessary, use a Phillips screwdriver to remove the shoulder
screws from the door.
B