Specific Safety Rules And Symbols - Metabo HPT CM 4SB2 Manual De Instrucciones

English
g) When wheel is binding or when interrupting a cut
for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes
to a complete stop. Never attempt to remove the
wheel from the cut while the wheel is in motion
otherwise kickback may occur.
Investigate and take corrective action to eliminate
the cause of wheel binding.
h) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re-enter the cut.
The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
i) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own
weight. Supports must be placed under the
workpiece near the line of cut and near the edge
of the workpiece on both sides of the wheel.
j) Use extra caution when making a "pocket cut"
into existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Contact
with a "live" wire will make exposed metal parts
of the tool "live" and shock the operator.
2. ALWAYS wear ear protectors when using the tool
for extended periods.
Prolonged exposure to high intensity
noise can cause hearing loss.
3. NEVER touch moving parts.
NEVER place your hands, fingers or
other body parts near the tool's moving
parts.
4. NEVER operate without all guards in place.
NEVER operate this tool without all guards or
safety features in place and in proper working
order. If maintenance or servicing requires the
removal of a guard or safety feature, be sure to
replace the guard or safety feature before resuming
operation of the tool.
5. Use right tool.
Don't force small tool or attachment to do the job
of a heavy-duty tool.
Don't use tool for purpose not intended —for
example— don't use circular saw for cutting tree
limbs or logs.
6. NEVER use a power tool for applications other
than those specified.
6
NEVER use a power tool for applications other than
those specified in the Instruction Manual.
7.
Handle tool correctly.
Operate the tool according to the instructions
provided herein. Do not drop or throw the tool.
NEVER allow the tool to be operated by children,
individuals unfamiliar with its operation or
unauthorized personnel.
8.
Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
9.
Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool's housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
10. Blades and accessories must be securely mounted
to the tool.
Prevent potential injuries to yourself or others.
Blades, cutting implements and accessories which
have been mounted to the tool should be secure
and tight.
11. Keep motor air vent clean.
The tool's motor air vent must be kept clean so
that air can freely flow at all times. Check for dust
build-up frequently.
12. Operate power tools at the rated voltage.
Operate the power tool at voltages specified on its
nameplate.
If using the power tool at a higher voltage than
the rated voltage, it will result in abnormally fast
motor revolution and may damage the unit and
the motor may burn out.
13. NEVER use a tool which is defective or operating
abnormally.
If the tool appears to be operating unusually,
making strange noises, or otherwise appears
defective, stop using it immediately and arrange
for repairs by a metabo HPT authorized service center.
14. NEVER leave tool running unattended. Turn power
off.
Don't leave tool until it comes to a complete stop.
15. Carefully handle power tools.
Should a power tool be dropped or struck against
hard materials inadvertently, it may be deformed,
cracked, or damaged.
16. Do not wipe plastic parts with solvent. Solvents
such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly
dampened with soapy water and dry thoroughly.
17. ALWAYS wear eye protection that meets the
requirement of the latest revision of
ANSI Standard Z87.1.