Control Modes - LEGRAND Wattstopper FSP-202D Instrucciones De Instalación

Ground
Non-Dimming
Driver
COM (Black)
NOTE: Dim Level functionality does not apply when
wired as shown above.
NOTE: Per UL, the 0-10V negative dimming wire color has been
changed from gray to pink.
The FSP-202D has five selectable modes, each of which has preset parameter settings. Once
the mode is selected, you have the ability to further customize operation by adjusting the Set
and the Time rotary trimpots.
Select the Mode and adjust the other rotary trimpots using a small screwdriver.
NOTE: A sixth mode, Test mode, is accessed automatically when mode A is selected. See
page 5 for details.
Set – This rotary trimpot is used to adjust three different parameters, depending on the current
mode: Desired Light Level (in foot candles), Hold Off Setpoint, and High Trim.
• The FSP-202D has a photocell which measures the ambient light continuously. In
Modes B, C, and D, this trimpot will adjust the Desired Light Level, with a range from
0 footcandles to 200 footcandles, and the FSP-202D will then adjust the dimming of the
load so that the combined amount of ambient light and electric light reaches the desired
light level. When this trimpot is set to the minimum position, the daylight control is disabled
and the FSP-202D will adjust the light level based only on occupancy without regard to
ambient light.
• In Mode A, this trimpot determines the light level for the Hold Off Setpoint, with a range from 0 footcandles to 200 footcandles.
When set to the minimum position, the light level hold off set-point is disabled.
• In Mode E, this trimpot controls the current dimming level, allowing visual confirmation of the High Trim level. The high trim level
is used to calculate the low dim amount, which varies based on the mode, as described below. It also determines the maximum
lighting level in Mode A, and if the photocell is disabled, determines the maximum lighting level for Modes B, C, and D.
Neutral
Line
BZ-200 Power Pack
120 – 277 VAC (1 I ), 50/60 Hz
20A Ballast/ELV/MLV/Tungsten/LED
LISTED
16A E-Ballast/CFL
Appliance
Control
1HP @ 120/240VAC
88T9
20A 120VAC Plug Load – Receptacle
Class 2 Output White Power Pack Red Lighting
Neut.
Load
24 VDC, 225 mA Switch
Black Red
Hot Green
UL 2043 Plenum Rated
Ground
Control
Common Any 3-Wire
24VDC
+24VDC
Sensor
www.wattstopper.com • 800.879.8585
Class 2 16094r1
wiring only
+VDC (Red)
CTRL (Blue)

CONTROL MODES

WIRING
Dimming
Driver
0-10V – (Pink)
0-10V + (Purple)
Dim-to-Off
Driver
COM/GND (Black)
0-10V – (Pink)
0-10V + (Purple)
Wiring with an external DC power supply
3
Ground
BZ-200 Power Pack
120 – 277 VAC (1 I ), 50/60 Hz
20A Ballast/ELV/MLV/Tungsten/LED
16A E-Ballast/CFL
1HP @ 120/240VAC
20A 120VAC Plug Load – Receptacle
Class 2 Output
24 VDC, 225 mA
UL 2043 Plenum Rated
Class 2
wiring only
COM (Black)
+VDC (Red)
CTRL (Blue)
Ground Neutral Line
+VDC Output (Red)
10V
C
B
D
A
E
Mode
Neutral
Line
LISTED
Appliance
Control
88T9
White Power Pack Red Lighting
Neut.
Switch Load
Black Red
Hot
Green
Ground
Control
Common Any 3-Wire
24VDC
+24VDC Sensor
www.wattstopper.com • 800.879.8585
16094r1
1V
15M
30S 30M
Time