Makita DDF483 Manual De Instrucciones página 7

Ocultar thumbs Ver también para DDF483:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 37
NOTE: When the tool is overheated, the tool stops
automatically and the lamp starts flashing. In this
case, release the switch trigger. The lamp turns off in
one minute.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Reversing switch action
► Fig.6: 1. Reversing switch lever
CAUTION:
Always check the direction of
rotation before operation.
CAUTION:
Use the reversing switch only after
the tool comes to a complete stop. Changing the direc-
tion of rotation before the tool stops may damage the tool.
CAUTION:
When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
Adjusting the fastening torque
► Fig.8: 1. Adjusting ring 2. Graduation 3. Arrow
The fastening torque can be adjusted in 21 levels by turning the adjusting ring. Align the graduations with the arrow
on the tool body. You can get the minimum fastening torque at 1 and maximum torque at
The clutch will slip at various torque levels when set at the number 1 to 20. The clutch does not work at
the
marking.
Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which
torque level is required for a particular application.
The following shows the rough guide of the relationship between the screw size and graduation.
Graduation
Machine screw
Wood
Soft wood
screw
(e.g. pine)
Hard wood
(e.g. lauan)
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
1
2
3
4
5
6
M4
Speed change
► Fig.7: 1. Speed change lever
CAUTION:
fully to the correct position. If you operate the
tool with the speed change lever positioned halfway
between the "1" side and "2" side, the tool may be
damaged.
CAUTION:
while the tool is running. The tool may be damaged.
Displayed
Number
1
2
To change the speed, switch off the tool first. Push
the speed change lever to display "2" for high speed
or "1" for low speed but high torque. Be sure that the
speed change lever is set to the correct position before
operation.
If the tool speed is coming down extremely during the
operation with display "2", push the lever to display "1"
and restart the operation.
7
8
9
10
11
M5
ɸ3.5 x 22
ɸ4.1x 38
ɸ3.5 x 22
Installing or removing driver bit/
drill bit
For Model DDF483 (optional accessory)
► Fig.9: 1. Sleeve 2. Close 3. Open
Turn the sleeve counterclockwise to open the chuck
jaws. Place the driver bit/drill bit in the chuck as far
as it will go. Turn the sleeve clockwise to tighten the
chuck. To remove the driver bit/drill bit, turn the sleeve
counterclockwise.
7 ENGLISH
Always set the speed change lever
Do not use the speed change lever
Speed
Torque
Low
High
High
Low
marking.
12
13
14
15
16
17
M6
ɸ4.1x 38
Applicable
operation
Heavy load-
ing operation
Light loading
operation
18
19
20
Tabla de contenido
loading

Este manual también es adecuado para:

Ddf083

Tabla de contenido