Makita HM1111C Manual De Instrucciones página 7

MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Lubrication
CAUTION:
• This servicing should be performed by Makita
Authorized Service Centers only.
This tool requires no hourly or daily lubrication because it
has a grease-packed lubrication system. It should be
lubricated every time the carbon brushes are replaced.
Send the complete tool to Makita Authorized Service
Center for this lubrication service. (Fig. 14)
Run the tool for several minutes to warm it up. Switch off
and unplug the tool.
Loosen the six screws and remove the handle. Note that
the top screws are different from other screws. (Fig. 15)
Disconnect the connector by pulling them. (Fig. 16)
Loosen the five screws on crank cap and remove the
crank cap. (Fig. 17)
Wipe out the old grease inside and replace with a fresh
grease (30 g). Use only Makita genuine hammer grease
(optional accessory). Filling with more than the specified
amount of grease (approx. 30 g) can cause faulty
hammering action or tool failure. Fill only with the
specified amount of grease.
CAUTION:
• Be careful not to damage the connector or lead wires
especially when wiping out the old grease.
To reassemble the tool, follow the disassembling
procedure in reverse.
CAUTION:
• Do not tighten the crank cap excessively. It is made of
resin and is subject to breakage.
• Be careful not to damage the connector or lead wires
especially when installing the handle. (Fig. 18)
Connect the connector firmly and then reinstall the
handle.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Bull point (SDS-max)
• Cold chisel (SDS-max)
• Scaling chisel (SDS-max)
• Clay spade (SDS-max)
• Bit grease
• Safety goggles
• Hammer grease
• Plastic carrying case
Noise
The typical A-weighted noise level determined according
to EN60745:
Model HM1111C
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Model HM1101C
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Model HM1111C
Work mode: chiseling function with side handle
Vibration emission (a
Uncertainty (K): 1.5 m/s
Work mode: chiseling function with side grip
Vibration emission (a
Uncertainty (K): 1.5 m/s
Model HM1101C
Work mode: chiseling function with side handle
Vibration emission (a
Uncertainty (K): 2.0 m/s
Work mode: chiseling function with side grip Vibration emission (a
Uncertainty (K): 1.5 m/s
• The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to
the trigger time).
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Demolition Hammer
Model No./ Type: HM1111C, HM1101C
are of series production and
ENG905-1
): 88 dB (A)
pA
): 99 dB (A)
WA
): 90 dB (A)
pA
): 101 dB (A)
WA
ENG900-1
2
): 7.5 m/s
h,CHeq
2
2
): 8.0 m/s
h,CHeq
2
2
): 13.5 m/s
h,CHeq
2
2
): 13.5 m/s
h,CHeq
2
ENG901-1
ENH101-14
7