Idiomas disponibles

Idiomas disponibles

THP2400A1027
Cover Plate Assembly
APPLICATION
Use the THP2400A1027 cover plate assembly with the Prestige
• THP2400A1027W - White
• THP2400A1027G - Gray
• THP2400A1027B - Black
Use the THP2400A1027 cover plate assembly to cover marks on the wall or to mount the thermostat to a 2 in. x 4 in.
electrical box.
The THP2400A1027 cover plate assembly contains two cover plates (small and large), one bracket, two #6-32 x 5/8 flat
head screws and two #6-32 x 1/4 pan head screws. See Fig. 1.
4-21/64
(110)
INSTALLATION
When Installing this Product...
1. Read these instructions carefully. Failure to follow them could damage the product or cause a hazardous
condition.
2. Check ratings given in the instructions and on the product to make sure the product is suitable for your
application.
3. Installer must be a trained, experienced service technician.
4. After installation is complete, check out product operation as provided in these instructions.
5-33/64
(140)
1-25/32
(46)
2-1/8
(54)
TWO #6-32 X 5/8 FLAT HEAD SCREWS
TWO #6-32 X 1/4 PAN HEAD SCREWS
Fig. 1. THP2400A1027 cover plate assembly.
®
IAQ thermostat.
6-7/8
(175)
1-25/32
(46)
5
(127)
2-1/8
(54)
LEVEL
LEVEL
BRACKET
M34262
INSTALLATION GUIDE
69-2759EFS-01
Tabla de contenido
loading

Resumen de contenidos para Honeywell THP2400A1027 Serie

  • Página 9: Conjunto De La Placa De Cobertura

    THP2400A1027 Conjunto de la placa de cobertura GUÍA DE INSTALACIÓN APLICACIÓN ® Utilice el conjunto de la placa de cobertura THP2400A1027 con los termostatos Prestige IAQ. • THP2400A1027W - Blanco • THP2400A1027G - Gris • THP2400A1027B - Negro Utilice el conjunto de la placa de cobertura THP2400A1027 para cubrir marcas en la pared o para instalar el termostato en un cajetín eléctrico de 2 in.
  • Página 10: Monte La Placa De Cobertura

    THP2400A1027 CONJUNTO DE LA PLACA DE COBERTURA PRECAUCIÓN Peligro eléctrico. Puede causar una descarga eléctrica o daños al equipo. Desconecte la energía antes de comenzar la instalación. Monte la placa de cobertura Monte la placa de cobertura directamente en la pared (Ver Fig. 2) 1.
  • Página 11 THP2400A1027 CONJUNTO DE LA PLACA DE COBERTURA Monte la placa de cobertura en un cajetín eléctrico vertical de 2 in. x 4 in. (5,1 cm x 10,2 cm) (Ver Fig. 3) 1. Coloque el soporte en el cajetín eléctrico. Inserte dos tornillos cabeza plana No. 6-32 X 5/8. Verifique la nivel- ación, si lo desea, y apriete los tornillos cabeza plana.
  • Página 12 2 in. x 4 in. (5,1 cm x 10,2 cm). Automatización y control desenlace Honeywell International Inc. 1985 Douglas Drive North ® Marca Registrada en los Estados Unidos © 2012 Honeywell International Inc. todos Golden Valley, MN 55422 Los Derechos Reservados 69-2759EFS—01 M.S. 11-12 customer.honeywell.com...

Este manual también es adecuado para:

Thp2400a1027wThp2400a1027gThp2400a1027b

Tabla de contenido