Bosch AQT 33-11 Manual Original página 16

All manuals and user guides at all-guides.com
OBJ_BUCH-2334-003.book Page 16 Thursday, March 16, 2017 9:28 AM
16 | English
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Operation
 To prevent damage to the appliance, do not allow it to
operate dry.
Starting
Attach water supply hose (not supplied) to the mains water
supply and machine.
Connect the product to the mains supply ensuring that the
mains switch is in the off position.
Open water tap.
Press the safety lock (back button on the gun handle) to re-
lease the trigger. Fully press the trigger until there is a con-
stant flow of water to clear the air from the machine and water
supply hose. Release trigger. Press the safety lock (front but-
ton on the gun handle).
Turn button on main switch. Point the power gun downwards.
Press the trigger safety lock to release the trigger. Fully press
the trigger.
Autostop function
The machine is designed to switch off the motor when the trig-
ger is released on the gun.
Working Advice
General
Ensure that the pressure washer is on level ground.
Do not overreach with the high pressure hose or move the
pressure washer by pulling the hose, this could cause the ma-
chine to become unstable and fall over.
Do not kink or drive a motor vehicle over the high pressure
hose. Do not expose the high pressure hose to sharp edges or
corners.
Never use a roto nozzle to clean motor vehicles.
Working advice for cleaning with detergents
 Only use cleaning agents suitable specifically for high
pressure washers.
We recommend that you use detergent sparingly for the sake
of the environment. Observe the recommended dilution on
the detergent label.
F 016 L81 709 | (16.3.17)
Recommended cleaning method
Step 1: Attach the fixed fan nozzle and remove the heavy dirt.
Step 2: Attach the foam bottle and spray on the detergent
sparingly.
Step 3: Rinse off the loosened dirt and detergent with the fan
nozzle.
Note: When cleaning vertical surfaces, apply the detergent
from bottom to top. When rinsing off, work from top to bot-
tom.
Use with alternative water sources
The power washer is self-priming and enables water to be
drawn in from containers or natural water sources. It is IM-
PORTANT that the water filter is in clean condition when in-
serting it at the water inlet, and that only clean water is drawn
in.
Open tanks/containers and natural water sources
Use the Self Priming accessory kit comprising:
– Inlet strainer with non return valve
– 3 m reinforced supply hose
– Universal coupling to the pressure washer
This enables the pressure washer to draw water up to 0.5 m
above the water level in the source in approximately 15 sec-
onds.
Fully immerse the 3 m hose into the water to displace the air
in the hose. Connect the 3 m hose to the power washer and
make sure that the inlet strainer remains under water.
With the spray gun removed, switch the power washer on and
operate it until water flows uniformly out of the high-pressure
hose. If no water is coming out of the high-pressure hose after
25 seconds, switch the power washer off and check all con-
nections. As soon as water flows out of the high-pressure
hose, switch the power washer off and connect the spray gu-
nand spray lance to begin with the work.
It is important that hose and couplings are of good quality and
are tightly connected, and that the seals are undamaged and
properly inserted. Loose connections can impede the priming
(drawing in).
Water Tanks with outlet connections
When connecting the pressure washer to a water tank with a
suitable tap outlet, first connect the supply hose (not provid-
ed) to the tank outlet, open the tap to allow the water to dis-
place all the air in the hose and then connect to the pressure
washer.
Bosch Power Tools