Bosch AQT 33-11 Manual Original página 15

All manuals and user guides at all-guides.com
OBJ_DOKU-44047-004.fm Page 15 Tuesday, April 11, 2017 9:17 AM
Pressure washer
Rated pressure MPa
Rated Flow l/min
Maximum inlet pressure MPa
Autostop function
Weight according to EPTA-
Procedure 01:2014
Protection class
Serial number
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Starting cycles generate brief voltage drops. Interference with other
equipment/machines may occur in case of unfavourable mains system
conditions. Malfunctions are not to be expected for system impedances
below 0.153 ohm.
Noise/Vibration Information
Sound emission values determined according to
EN 60335-2-79.
Typically the A-weighted noise levels of the product are:
Sound pressure level 85 dB(A); sound power level 94 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60335-2-79:
2 2
a =4 m/s , K=1.5 m/s .
h
Mounting and Operation
Action
Delivery Scope
Mounting cable bracket/in use storage for
gun
Connecting/disconnecting high pressure
gun to lance
Connecting/disconnecting nozzle
Connecting/disconnecting high pressure
water supply hose/nozzle
Connecting to the water supply
Switching On and Off
Adjust water jet
Connect detergent bottle
Clean nozzle
Clean the water filter
Transport
Storage
Selecting Accessories
Bosch Power Tools
Starting
AQT 33-11
7.4
Electrical Safety
4.7
Warning! Switch off, remove plug from mains
1
before adjusting, cleaning or if cable is cut,

damaged or entangled.
Your machine is double insulated for safety and requires no
kg 4.5
earth connection. The operating voltage is 230 V AC, 50 Hz
/II
(for non-EU countries 220 V, 240 V as applicable).
See serial number
For increased electrical safety use a Residual Current Device
(rating plate) on
(RCD) with a tripping current of not more than 30 mA. Always
pressure washer.
check your RCD every time you use it.
The supply cables must be inspected for signs of damage at
regular intervals and may only be used if in perfect condition.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Only use approved extension cables.
WARNING! Inadequate extension cables can
be dangerous. Extension cable, plug and sock-
et must be of watertight construction and in-
tended for outdoor use.
Extension cords, cables, leads, reels should only be used if
they comply with EN 61242/IEC 61242 or
IEC 60884-2-7.
If you want to use an extension cable when operating your
product, only the following cable dimensions should be used:
– Nominal Conductor Area of 1.5mm
of 20m for a Cord Extension Set
The connections (plugs and sockets) should be kept dry and
off the ground.
Figure Page
It is recommended that this is accomplished by means of a
cord reel which keeps the socket at least 60 mm above the
1 253
ground.
Note: If an extension cable is used it must be earthed and con-
2 253
nected through the plug to the earth cable of your supply net-
work in accordance with prescribed safety regulations.
3 254
Refer to the instruction manual of the extension cord, lead,
3 254
reel manufacturer and your local wiring regulations.
If in doubt contact a qualified electrician or the nearest Bosch
4 255
Service Centre.
5 255
For products not sold in GB:
6 256
WARNING: For your safety, it is required that the plug at-
7 256 tached to the product is connected with the extension cord.
The coupling of the extension cord must be protected against
8 257
splash water, be made of rubber or coated with rubber. The
9 257
extension cord must be used with a cable strain relief.
10 258
 Products sold in GB only: Your product is fitted with a
11 258
BS 1363/A approved electric plug with internal fuse
11 259
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
12 260
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
English | 15
2
to a max. cable length
F 016 L81 709 | (11.4.17)