Idiomas disponibles
Idiomas disponibles
x2
***
0---
ALT
follow the user guide
add. start
Add. 2ch
erase 64
language
stat
OK
vers
No total
- +
manoeuvres(in hundreds)
OK
n. cycles
- +
n. remotes
OK
- +
List of last 30 errors
err
0---
password
40
- GIOTTO BT A 30-60 S U / GIOTTO BT A 30-60 U
ACCESS MENUS Fig. 2
INSTALLATION MANUAL
150-
10--
hidden butt
release
hidden butt
release
Diagnostics
code
START E external start input activated
STRE
START I internal start input activated
STRI
OPEN input activated
OPEN
CLOSE input activated
CLS
TIMER input activated
TIME
STOP input activated
STOP
Activation of PHOT photocell input or, if configured as verified
PHOT
photocell, Activation of the associated FAULT input
Activation of PHOT OP opening photocell input or, if configu-
red as active verified photocell only when opening, Activation
PHOP
of the associated FAULT input
Activation of PHOT CL closing photocell input or, if configured
as active verified photocell only when closing, Activation of
PHCL
the associated FAULT input
Activation of BAR safety edge input or, if configured as ve-
BAR
rified safety edge, Activation of the associated FAULT input
Activation of BAR safety edge input on slave motor (opposing
door connection) or, if configured as verified safety edge,
BAR 2
Activation of the associated FAULT input
SWC motor closing limit switch input activated
SWC
SWO motor opening limit switch input activated
SWO
Photocell test failed
ER01
Safety edge test failed
ER02
Opening photocell test failed
ER03
Control unit
Closing photocell test failed
software version
ER04
bft . . .
Safety edge test on slave motor failed (opposite leaves
ER05
+/-
connection)
8k2 safety edge test failed
er06
0000
+/-
Board hardware test error
ER1x*
No radio control
devices memorised
Encoder error
ER2x**
00
+/-
Reverse due to obstacle - Amperostop
ER3x*
Thermal cutout
ER4x*
01.33
OK
Communication error with remote devices
ER5x*
02.01
ER70, ER71
Internal system supervision control error.
ER74, ER75
........
30.15
Consistency error of the control unit's parameters (Logics and Parameters)
ER72
+/-
D-track parameter error
ER73
limit switch error
ErFx*
10--
1520
ok
See PARAMETERS MENU
See LOGIC MENU
desired button
desired button
See RADIO MENU
DESCRIPTION
* X = 0,1,...,9,A,B,C,D,E,F
150-
1520
Request with Protection Level logic set to 1, 2, 3, 4
Scroll up
Scroll down
Con rm/Switch on display
Exit Menù
NOTES
Check photocell connection and/or logic settings
Check safety edge connection and/or logic settings
Check photocell connection and/or parameter/
logic setting
Check photocell connection and/or parameter/
logic setting
Check safety edge connection and/or parameter/
logic settings
Check safety edge connection and/or parameter/
logic settings
- C h e c k
c o n n e c t i o n s
-Hardware problems with board (contact techni-
cal assistance)
Check the cable, the encoder card and the motor
direction (if necessary) and reset the card
Check for obstacles in path
Allow automated device to cool
Check connection with serial-connected accessory
devices and/or expansion boards
Try switching the board off and back on again.
If the problem persists, contact the technical as-
sistance department.
Pressing OK the detected settings are confirmed. The
board will keep on working with the detected settings.
The board settings must be checked (Parameters and Logics)
Pressing OK, the board will keep on working with D-track
as a default.
An autoset is required
Check limit switch connections
prg
*** Password entry.
t o
m o t o r
