Maintenance - SPARKY VC 1321MS Instrucciones De Uso

▪ Plug the power tool into the built-in socket (27) of the
vacuum cleaner.
▪ Insert the vacuum cleaner plug into the mains supply
socket.
▪ Set the vacuum cleaner switch (2) to the "ON" posi-
tion "II".
▪ Switch on the power tool.
The vacuum cleaner will switch on automatically a few
seconds after you switch on the power tool. When you
switch off the power tool, the vacuum cleaner will also
switch off after a pre-set delay.
WET VACUUM CLEANING
WARNING: Never vacuum up hazardous
materials.
▪ Make sure that the appliance is unplugged.
▪ Check to make sure that the tank (7) is free of dust
and dirt.
▪ The appliance is shipped from the factory with a car-
tridge filter. Remove the cartridge filter (21), which is
not appropriate for wet vacuum cleaning.
▪ Remove the dust bag (14) and the dry filter (22) in case
you have used them prior to wet vacuum cleaning.
▪ Place the foam filter (19) (Fig.12) on the filter basket.
▪ Place the upper section on the tank and close the
clamps.
▪ Place the large end of the hose on the front air intake
stub on the tank.
▪ Select the necessary nozzle (13,15) or tube (11) and
place it on the hose (10).
▪ Make sure that the ON/OFF switch (2) of the appliance
is in "OFF" position "O" before you plug the appliance.
▪ Insert the plug into the socket.
▪ Switch the motor on by placing the ON/OFF switch (3)
in position "I".
▪ When you have finished wet vacuuming, switch the
motor off by putting the ON/OFF switch (2) into the
„OFF" position „O".
▪ Unplug the vacuum cleaner.
▪ After use, empty and dry the tank (7).
Tip: If you want to vacuum up a large quantity of liquid
from a sink or a tank, please don't put the entire suc-
tion nozzle in the liquid; rather leave a little space so that
some air can also be drawn in along with the liquid.
The appliance is equipped with a float switch (5) (Fig.13)
that will stop the vacuuming when the tank is full. You will
notice that suction has stopped by the motor now run-
ning faster. At this event, switch the appliance off and
unplug it.
Be aware that the full tank can be very heavy.
Remove the cap from the drain outlet (25) and pour the
rest of the liquid into a suitable tank or drain. Then, you
can continue vacuuming after you have replaced the
drain outlet cap.
After wet vacuuming, switch off the appliance and un-
plug it. Empty the container and clean/dry it inside and
outside prior to storage.
Original instructions
IMPORTANT! After wet vacuuming, please proceed as
described in the section entitled „Dry vacuum cleaning"
before you attempt to dry vacuum again.
BLOWING FUNCTION
Remove the upper hook (23) for winding up the cable.
Insert the larger end of the hose into the orifice in the up-
per rear part of the vacuum cleaner. The hose connector
tooth shall align with the groove in the blow connector.
(Fig.14)
WARNING: Never turn the air flow towards
people, animals or objects as the outcoming air may
be hot.
ACCESSORIES
MODEL
Hose set
Air control handle
2-part plastic tube
Crome coated metal
telescopic tube
Dust bag
Dry filter
Foam filter
PET cartridge filter
Floor nozzle
Combo nozzle
Crevice nozzle
Wheels and castors
Castor pedestals
WARNING: Use only original SPARKY ac-
cessories. The use of non original spare parts or
accessories presents potential danger and voids the
guarantee.

Maintenance

▪ Make sure that the appliance is not plugged into the
power mains.
▪ Take out the suction hose (10) from the tank.
▪ Release the clamps (Fig.1) and remove the upper sec-
tion from the tank (Fig.2).
▪ Clean up any dirt or debris from the tank and hose.
▪ Clean the foam filter (19) by washing it with a mild de-
tergent.
▪ Check the hose and connections and inspect the
power cord for any damage.
▪ When the foam foam filter (19) is removed, check
the float (5). To do this, take the upper section by the
handle and turn it carefully so that the filter basket is
VC 1321MS VC 1431MS
• •
•
•
•
• •
•
• •
• •
•
•
• •
2 wheels + 2 wheels +
2 castors 2 castors
2 2
7
EN