Blade Sharpening - Worx wG783E Manual Del Usuario

shake the grass down to the back end
of the bag. Also clean out any grass or
debris which may be packed around the
discharge opening. replace the grass
collection bag.
5) If mower should start to vibrate
abnormally, release switch lever to turn
mower "OFF" . Check immediately for
cause. Vibration is a warning of trouble.
Do not operate mower until a service
check has been made.
aLwayS rELEaSE SwITch LEVEr TO
6)
TUrN mOwEr "OFF" aND rEmOVE
SaFETy kEy whEN LEaVING IT
UNaTTENDED EVEN FOr a ShOrT
pErIOD OF TImE.
MAINTENANCE
warNING: Stop the mower and
remove the safety key before
removing the grass bag.
NOTE: to ensure long and reliable service,
perform the following maintenance
procedures regularly. Check for obvious
defects such as a loose, dislodged or a
damaged blade, loose fittings, and worn
14 14
or damaged components. Check that the
covers and guards are all undamaged and
are correctly attached to mower. Carry out
any necessary maintenance or repairs before
operating mower. If the mower should
happen to fail despite regular maintenance,
please call our customer helpline for advice.

bLaDE SharpENING

KEEP BLADE SHArP FOr BESt MOWEr
PErFOrMANCE. A DuLL BLADE DOES NOt
Cut GrASS CLEANLY Or MuLCH PrOPErLY.
WEAr PrOPEr EYE PrOtECtION WHILE
rEMOVING, SHArPENING, AND INStALLING
BLADE ENSurE tHAt SAFEtY KEY IS
rEMOVED.
Sharpening the blade twice during a mowing
season is usually sufficient under normal
circumstances. Sand causes the blade to dull
quickly. If your lawn has sandy soil, more
frequent sharpening may be required.
rEPLACE BENt Or DAMAGED BLADE
IMMEDIAtELY.
Cordless lawn mower
whEN SharpENING ThE bLaDE:
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting
angle.
3. Sharpen cutting edges on both ends
of blade, removing equal amounts of
material from both ends.
TO SharpEN bLaDE IN a VISE (See L)
1. Be sure the switch lever is released, the
blade has stopped and the safety key
removed before removing the blade.
2. remove blade from mower. See
instructions for removing and attaching
blade.
3. Secure blade L-1 in a vise L-2.
4. Wear safety glasses and be careful not to
cut yourself.
5. Carefully file the cutting edges of
the blade with a fine tooth file L-3 or
sharpening stone.
6. Check balance of blade. See instructions
for blade balancing.
7. replace blade on mower and tighten
securely. refer to instructions below.
bLaDE baLaNcING (See m)
Check balance of blade by placing center hole
in blade M-1 over a nail or screwdriver shank
M-2, clamped horizontally in a vise M-3. If
either
end of the blade rotates downward, file that
end. Blade is properly balanced when neither
end drops.
bLaDE maINTENaNcE (See N1, N2)
renew your metal blade after 50 hours
mowing or 2 years, which ever is the sooner-
regardless of condition.
Follow these procedures to remove and
replace the blade. You will need garden gloves
(not provided) and a spanner wrench (not
provided) to remove the blade. Hold the blade
(15) and unscrew the blade bolt (14) counter-
clockwise using a spanner wrench, and then
remove blade.
to re-assemble, position the blade (15) with
the cutting edges towards the ground. then
securely tighten the blade bolt (14).
EN