ProTeam GoFree Flex Pro II Manual Del Usuario página 11

Ocultar thumbs Ver también para GoFree Flex Pro II:
Tabla de contenido
Figure G
Figure H
Figure I
Figure J
Figure K
Figure L
Figure M
Figure N
Figure O
OPERATING
INSTRUCTIONS
WEARING THE BACKPACK VACUUM
1. Loosen the shoulder straps and the waist belt.
Lift the vacuum and slide your arms through the
straps (Figure G). The upper harness can also be
adjusted by tightening or loosening the upper
harness buckles for a custom fit.
2. Connect the waist strap (Figure H).
3. Tighten the waist belt by grabbing the ends of
the straps and pulling each end toward each
other and then directly outward from the center
of the body. It is very important that the weight
of the unit be concentrated on your hips rather
than your shoulders (Figure I).
4. Adjust the shoulder straps so that the unit fits
comfortably, but the weight is still concentrated
on your hips (Figure J).
5. Connect the sternum strap buckle (Figure K) and
slide the strap up or down on the strap for the
best fit (Figure L).
OPERATING THE BACKPACK
VACUUM
1. Fasten the ends of the wands together. Pull
back to open purple latch on lower half of the
wand. Find the notch on the inside of lower
half and the groove on the outside of the
upper half - they must align. Insert the upper
half into the lower by aligning the notch and
groove. To tighten into position, close the
purple latch when wand is at desired height
(Figure M). If wand does not stay at desired
height, pull open the purple latch, tighten
the Phillips screw as necessary, and close the
purple latch again.
2. Attach the floor tool to end of wand. Align the
brass ring with the groove on the floor tool to
ensure a secure fit (Figure M).
3. Twist the wand into the end of the hose (Figure
M).
4. Turn the unit on to desired power level (I = low
speed, II = high speed), and proceed with vacu-
uming.
5. The on/off switch is conveniently located on the
waist belt of the backpack vacuums (Figure N).
PROPER VACUUMING MOTION FOR LARGE
AREAS
1. Begin with the wand parallel to your body.
2. Draw the top of the wand in toward your waist
and twist at the waist walking backward or
forward, in a side-to-side motion (Figure O).
3. The motion is similar to mopping and keeps the
upper body and arms from tiring.
INSTRUCCIONES DE
FUNCIONAMIENTO
USO DE LA ASPIRADORA
TIPO MOCHILA
1. Afloje las correas de los hombros y las correas de
la cintura. Levante la aspiradora y meta los brazos
entre las correas (Figura G). El arnés superior
también puede ajustarse ajustando o aflojando
sus hebillas para tener un calce personalizado.
2. Conecte las correas de la cintura (Figura H).
3. Ajuste la correa de cintura tomando los extremos
de las correas y tirando de cada extremo hacia
el otro y luego directamente hacia afuera desde
el centro del cuerpo. Es muy importante que el
peso de la unidad se concentre en sus caderas y
no en sus hombros (Figura I).
4. Ajuste las correas de los hombros para que la
unidad se acomode bien, pero con el peso
siempre concentrado en las caderas (Figura J).
5. Conecte la hebilla de la correa ajustable al
esternón (Figura K) y deslice dicha correa hacia
arriba o hacia abajo por la otra correa para lograr
el mejor ajuste posible (Figura L).
FUNCIONAMIENTO DE LA
ASPIRADORA TIPO MOCHILA
1. Fije juntos los extremos de los tubos. Jale hacia
atrás para abrir el sujetador púrpura ubicado en
la mitad inferior del tubo. Encuentre la muesca
ubicada en el interior de la mitad inferior y la
ranura ubicada en el exterior de la mitad superior.
La muesca y la ranura deben estar alineadas.
Inserte la mitad superior en la mitad inferior
alineando la muesca y la ranura. Para realizar el
apriete en la posición correcta, cierre el sujetador
purpura cuando el tubo esté a la altura deseada
(Figura M). Si el tubo no permanece a la altura
deseada, jale el sujetador púrpura para abrirlo,
apriete el tornillo Phillips según sea necesario y
cierre de nuevo el sujetador púrpura.
2. Conecte la herramienta de piso al extremo del
tubo. Alinee el aro de bronce con la muesca en
la herramienta de piso para garantizar un ajuste
seguro (Figura M).
3. Gire el tubo en el extremo de la manguera.
(Figura M)
4. Encienda la unidad al nivel de potencia deseado
(I = baja velocidad, II = alta velocidad) y comience
a aspirar.
5. El interruptor de encendido/apagado está
ubicado convenientemente en la correa de la
cintura de las aspiradoras tipo mochila (Figura N).
MOVIMIENTO DE ASPIRACIÓN
ADECUADO PARA ÁREAS GRANDES
1. Comience con el tubo paralelo a su cuerpo.
2. Lleve la parte superior del tubo hacia su cintura
y gire la cintura mientras camina hacia atrás o
hacia delante, con un movimiento de lado a lado
(Figura O).
3. El movimiento es similar a trapear y evita que la
parte superior del cuerpo y los brazos se cansen.
ProTeam Owner's Manual / Manual del propietario de ProTeam / Mode d'emploi ProTeam – 9
MODE D'EMPLOI
PORT DE L'ASPIRATEUR DORSAL
1. Desserrez les bandoulières et le ceinturon.
Soulevez l'aspirateur et placez les sangles sur
vos épaules (Figure G). Pour un ajustement sur
mesure, resserrez ou desserrez les boucles sur le
harnais.
2. Bouclez le ceinturon (Figure H).
3. Resserrez la ceinture en agrippant les extrémités
des courroies et en les tirant l'une vers l'autre,
puis vers l'extérieur. Il est très important que le
poids de l'appareil repose sur vos hanches plutôt
que vos épaules (Figure I).
4. Ajustez les bandoulières de manière à ce que le
port de l'appareil soit confortable, mais que son
poids soit toujours concentré sur vos hanches
(Figure J).
5. Boucler la courroie de sternum (Figure K) et
glisser la sangle vers le haut ou vers le bas pour
un meilleur ajustement (Figure L).
UTILISATION DE L'ASPIRATEUR
DORSAL
1. Attachez ensemble les extrémités du tube-
rallonge. Tirez pour ouvrir le loquet pourpre sur la
partie inférieure du tube. Repérez l'encoche sur la
paroi intérieure du tube du bas et la rainure sur la
paroi extérieure du tube du haut – elles doivent
être alignées. Insérez le tube du haut dans le tube
du bas en alignant l'encoche et la rainure. Serrez
en position, puis fermez le loquet pourpre lorsque
le tube-rallonge a atteint la longueur désirée
(Figure M). Si le tube-rallonge ne demeure pas
à la hauteur désirée, ouvrez le loquet pourpre,
puis serrez-le à l'aide d'un tournevis Phillips si
nécessaire. Refermez ensuite le loquet pourpre.
2. Attachez l'accessoire de plancher à l'extrémité
du tube. Alignez l'anneau en laiton sur cannelure
de l'accessoire afin d'obtenir une bonne fixation
(Figure M).
3. Avec un mouvement de torsion, fixez le tube à
l'extrémité du boyau (Figure M).
4. Mettez l'aspirateur de puissance souhaité (I =
basse vitesse, II = haute vitesse) en marche et
effectuez le travail.
5. Le commutateur marche/arrêt se situe sur le
ceinturon de l'aspirateur dorsal (Figure N).
COMMENT PASSER L'ASPIRATEUR SUR
UNE GRANDE SURFACE
1. Placez le tube d'aspiration parallèlement à votre
corps.
2. Tirez le haut du tube vers votre taille, puis tournez
votre taille pendant que vous marchez vers
l'arrière ou l'avant, en effectuant un mouvement
de va-et-vient latéral (Figure O).
3. Ce mouvement est semblable à celui utilisé pour
passer la vadrouille et diminue la fatigue du haut
du corps et des bras.
Tabla de contenido
loading

Este manual también es adecuado para:

1076420

Tabla de contenido