Tabla de contenido
Idiomas disponibles
Idiomas disponibles
The smaller the gauge number of the wire, the greater the capacity of the cord. for example: a 14-gauge cord
can carry a higher current than a 16-gauge cord. When using more than one extension cord to make up the total
length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord for
more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure it is marked with the suffix "W-A" ("W" in Canada) to
indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged
extension cord or have it repaired by a qualified person before using it.
• Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
Recommended Minimum Wire Gauge for Extension Cords (120 Volt)
Nameplate
Extension Cord Length
Amperes
25 Feet
(At Full Load)
0–2.0
18
2.1–3.4
18
3.5–5.0
18
5.1–7.0
18
7.1–12.0
18
12.1–16.0
14
16.1–20.0
12
SPECIFIC SAFETY RULES FOR BELT SANDERS
WARNING:
FROM REPEATED USE) REPLACE STRICT ADHERENCE TO PRODUCT SAFETY RULES. If
you use this tool unsafe or incorrectly, you can suffer serious personal injury!
Always wear safety glasses or goggles.
•
safety glasses. use certified safety equipment. Protective eye wear should comply with ANSI Z87.1 standards
Use adequate and appropriate respiratory protection.
•
products, paints and woods may expose the user to dust containing hazardous substances.
Wear ear/hearing protectors
•
high intensity noise can cause hearing loss.
Always hold the tool firmly.
•
Hold the tool firmly with both hands.
•
that may result from loss of control.
Keep hands away from rotating parts
•
Make sure the belt is not contacting the workpiece
•
Do not wet sand with this sander.
•
motor housing is an electrical shock hazard.
Do not sand metal of any kind with your belt sander.
•
sanding screws, nails, or other metals which may ignite dust particles.
Sanding lead-based paint is not recommended.
•
removed by a professional.
Empty the dust bag frequently and after completion of sanding.
•
accumulation of fine sanding dust particles may self ignite and cause a fire, especially when sanding surfaces
coated with polyurethane, varnish, shellac, etc. Do not throw sanding dust on an open fire. Do not mix sanding
dust with oil or water, this mixture may, over time, result in spontaneous combustion.
Unplug the sander before changing sanding belts or accessories.
•
start-up may occur if the sander is plugged in, causing personal injury.
Never leave the trigger locked "ON".
•
"off". An accidental start-up could cause personal injury.
50 Feet
75 Feet
18
18
18
16
14
12
10
DO NOT LET COMFORT OR FAMILIARITY WITH PRODUCT (GAINED
when using this tool for extended periods. Prolonged exposure to
Do not leave the tool running unless hand held.
100 Feet
18
18
18
16
16
14
14
12
12
10
10
10
8
8
Normal prescription eye or sunglasses are not
Always use both front and rear handles to prevent injury
.
before the switch is turned on.
This tool has not been waterproofed; any liquid entering the
Lead-based paint should only be
Before plugging in the tool, check that the trigger lock is
150 Feet
200 Feet
16
16
14
14
12
12
12
10
8
8
8
6
6
6
using this tool to sand some
Sparks may be caused by
The
An accidental
5
Tabla de contenido
