Tabla de contenido
a
Quick start guide
Telescope
For more information see the extended manual online:
ned.is/scte7070wt
Intended use
The Nedis SCTE7070WT is a telescope with a maximum focal length
of 700 mm.
This product is included with three eyepieces, an erecting lens and
a Barlow lens.
This product can be used by children aged from 6 years and above
and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the product in a safe
way and understand the hazards involved. Children shall not play
with the product. Cleaning and user maintenance shall not be done
by children without supervision.
Any modification of the product may have consequences for safety,
warranty and proper functioning.
Specifications
Product
Article number
Aperture
Objective focal length
Max. tripod height
Finder scope
Diagonal Prisms
Acceddoness
Eyepiece
Magnification
4 mm
175 x
12.5 mm
56 x
20 mm
35 x
Main parts (image A)
1
Eyepiece (3 lenses included)
2
Erecting lens / Barlow lens
Focus tube
3
Finder scope bracket
4
5
Finder scope
Bracket mounting screw
6
Bracket
7
8
Azimuth lock
Main body
9
Objective lens
q
Safety instructions
-
WARNING
• Ensure you have fully read and understood the instructions in
this document before you install or use the product. Keep the
packaging and this document for future reference.
• Only use the product as described in this document.
• Do not use the product if a part is damaged or defective. Replace
a damaged or defective product immediately.
• Place the product on a stable and flat surface.
• Do not use the product to watch the sun or any other light
source. Looking directly at the sun can cause permanent eye
damage.
SCTE7070WT
Telescope
SCTE7070WT
70 mm
700 mm
125 cm
5 x 24
90 °
1.25"
Magnification
Magnification
with 1.5x
with 3x Barlow
erecting lens
lens
263 x
525 x
84 x
168 x
53 x
105 x
w
Objective lens cover
e
Diagonal periscope viewer
Eyepiece attachment screw
r
Focus knob
t
y
Lens holder
Micro adjustable altitude
u
control
i
Tripod head
Tripod
o
Tripod leg lock
p
• Never use your telescope to project sunlight onto another
surface, the internal heat build-up will damage the optical
elements of the telescope.
• Do not drop the product and avoid bumping.
• Do not expose the product to water or moisture.
• Children of less than 3 years should be kept away.
• This product can be used by children aged from 6 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
product in a safe way and understand the hazards involved.
Children shall not play with the product. Cleaning and user
maintenance shall not be done by children without supervision.
• Usage by children should be supervised at all times.
• This product may only be serviced by a qualified technician.
Installing the product
1. Unlatch the three tripod leg locks A
A
o
out to full extension.
2. Spread A
and lock A
o
3. Connect the three legs A
provided nuts and bolts.
4. Install the lens holder A
wingnuts and bolts.
5. Place the bracket A
7
screw A
to tighten A
6
6. Place the main body A
A
to secure A
.
6
9
7. Slide the micro adjustable altitude control A
on the side of A
7
.
8. Tighten the other end of A
9. Unscrew and remove the bolts of the finder scope bracket A
10. Place A
onto A
4
9
Make sure A
is facing the same direction as the objective lens
4
5
A
q
.
11. Install the diagonal periscope viewer A
A
3
.
-
Make sure the end of A
A
3
.
12. Place the desired eye piece A
secure the eyepiece.
-
Only use the Barlow lens A
viewing results. Place the Barlow lens A
Place one of A
into the erecting lens or Barlow lens A
4
1
increase the magnification.
Using the product
-
Make sure the product is placed on a flat and stable surface.
-
Only use the erecting lens A
astronomical observations.
1. Remove the objective lens cover A
2. Look through the finder scope A
• Untight the Azimuth lock A
angle of A
9
.
• Adjust A
to change the vertical viewing angle of A
u
3. Untighten the adjustment nuts of A
object.
4. Move A
5
until you can see the object.
5. Tighten the adjustments nuts of A
6. Look through A
to see the target object.
1
7. Use the focus knob A
t
-
Apply small and slow adjustments for focusing.
-
Place A
back on the product when not in use.
w
4
and pull each of the legs
p
in place to secure A
p
o
.
to the tripod head A
o
i
between A
y
o
using the provided
into A
i
and rotate the bracket mounting
7
.
in A
9
7
and rotate the locking screws
u
through the hole
with the screw to A
u
9
and tighten the bolts.
e
into the focus tube
e
without the screw is inserted into
into A
1
e
. Tighten the screw to
without A
2
e
to get the best
directly into A
2
2
to observe landscapes, not
w
.
5
to find the target object.
8
to change the horizontal viewing
5
if you do not see the
5
again.
to focus on the object.
using the
.
4
.
3
.
to
2
9
.
Tabla de contenido
