JB Systems SPACE COLOR Laser Manual De Instrucciones página 6

ENGLISH
DMX-CONFIGURATION OF SPACE-COLOR LASER:
CHANNEL VALUE DESCRIPTION
1 000-200 Stepper motor scanning speed (from fast to slow)
201-254 Space color laser is switched to stand-alone mode (use the AUTO/MUSIC
switch to put the laser in the desired mode)
255 Complete reset (to be used while switching from stand-alone to DMX mode)
2 000-014 Pattern 1
015-020 Pattern 2
023-027 Pattern 3
028-034 Pattern 4
035-041 Pattern 5
042-048 Pattern 6
049-055 Pattern 7
056-062 Pattern 8
063-070
Pattern 9
071-076 Pattern 10
077-083 Pattern 11
084-090 Pattern 12
091-097 Pattern 13
098-104 Pattern 14
105-111 Pattern 15
112-118 Pattern 16
119-125 Pattern 17
126-132 Pattern 18
133-140 Pattern 19
141-153 Pattern 20
154-160 Pattern 21
161-167 Pattern 22
168-174 Pattern 23
175-181 Pattern 24
182-188 Pattern 25
189-195 Pattern 26
196-202 Pattern 27
203-210 Pattern 28
211-216 Pattern 29
217-223 Pattern 30
224-230 Pattern 31
231-251 Pattern 32
252-255 Pattern 33
3 000-255 Rotation of the patterns
4 000-255 Zooming: pattern size (from small to big)
5 000-255 Panning movement (X-axis: left to right - value 128 is middle position)
6 000-255 Tilt movement (Y-axis: up and down - value 128 is middle position)
7 000 Blackout
001-254 Blanking frequency (from low to high)
255 No blanking
8 000-055 Beam color: Red
056-083 Beam color: Green
084-111 Beam color: Yellow
112-139 Beam color: Red & Green
140-167 Beam color: Yellow & Green
168-195 Beam color: Red & Yellow
196-254 Beam color: Red, Green & Yellow
255 Beam color: Original color of the pre-programmed patterns
JB SYSTEMS®
USER MANUAL
7/52 SPACE-COLOR Laser
ENGLISH
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during
servicing.
 Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened
and may not be corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally
free from any deformation.
 When an optical lens is visibly damaged due to cracks or deep scratches, it must be
replaced.
 The mains cables must be in impeccable condition and should be replaced immediately
when even a small problem is detected.
 In order to protect the device from overheat the cooling fans (if any) and ventilation
openings should be cleaned monthly.
 The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
 The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surroundings can cause
greater accumulation of dirt on the unit's optics.
 Clean with a soft cloth using normal glass cleaning products.
 Always dry the parts carefully.
 Clean the external optics at least once every 30 days.
 Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified
personnel!
SPECIFICATIONS
Mains Input: AC 230V, 50Hz
Fuse: 250V 1.5A slow blow (20mm glass)
Sound Control: Internal microphone
DMX connections: 3pin XLR male / female
DMX channels: 8 channels
001  255
DMX starting address:
Laser Power: 30mW Green CW laser (λ = 532nm)
80mW Red CW laser (λ = 650nm)
Laser radiation class: 3B
Laser Safety Standard: EN60825-1:1994 + A1:2002 + A2:2002
Size: 26 x 30x 10cm
Weight: 5,5kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS®
USER MANUAL
8/52 SPACE-COLOR Laser