Idiomas disponibles
Idiomas disponibles
Rinse aid and refined salt
Only use products which have been
EN
specifically designed for dishwashers.
Do not use table salt or industrial salt, or
washing up liquid.
If using a multi-functional product it is not necessary to
add rinse aid; however, we recommend that you add salt,
especially if you live in an area where the water is hard
or very hard. Follow the instructions given on the
packaging.
*
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water
runs off surfaces more readily and therefore does not leave
streaks or marks.
The rinse aid dispenser should be filled:
• When the LOW RINSE AID
panel is illuminated;
If you are not completely satisfied with the drying results,
you may adjust the quantity of rinse aid used. Use a
screwdriver to turn the dosage adjuster (F) to one of the 6
pre-set positions (the default position is set to 4):
• If there are streaks on the crockery, set the adjustment
device to a lower number (1-3).
• If drops of water remain on the crockery or if there are
limescale marks present after the cycle has finished, set
the adjuster to a higher number (4-6).
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of
appliance, supplies water without limescale which is then used
to wash the crockery.
This dishwasher offers a setting which helps to reduce
pollution and optimises washing performance in accordance
with the water hardness level in your area. This information can
be obtained from the organisation which supplies your
household with water.
- Open the door and switch on the machine by pressing the
ON/OFF button.
- Press the P button and hold for approximately 5 seconds;
two short beeps will sound and the indicator light
corresponding to the set degree of hardness will flash
slowly on the display (the water softening system is set to
number 2).
20
All manuals and user guides at all-guides.com
*
*
indicator light on the control
1. Open the dispenser by turning the
lid (G) in an anticlockwise direction.
2. Pour in the rinse aid, making sure
it does not overflow from the
dispenser. If this happens, clean the
spill immediately with a dry cloth.
F
3. Screw the lid back on.
NEVER pour the rinse aid
G
directly into the appliance tub.
- Press the P button repeatedly until the desired hardness
level has been reached (1-2-3-4-5
table).
E.g. hardness 1 (indicator light 1 flashing)
hardness 2 (indicator light 1 illuminated, indicator light 2
flashing).
hardness 3 (indicator lights 1 and 2 illuminated, indicator light
3 flashing and so on), up to a maximum of 5
- To exit the function, wait approximately 30 seconds or switch off
the machine using the ON/OFF button.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
Water Hardness Table
°dH
°fH
0
11
0
20 1.1
12
17
21
30 2.1
17
34
31
60 3.1
34
50
61
90 6.1
For values between 0°f and 10°f, we do not
recommend the use of salt.
* this setting may cause a slight increase in the
duration of the cycle.
(°dH = hardness measured in German degrees - °f =
hardness measured in French degrees - mmol/l = millimoles
per litre)
Measuring out the refined salt
In order to achieve the best possible results using a wash
cycle, make sure that the dispenser is never empty. Refined
salt removes limescale from the water, thus avoiding the
formation of deposits on crockery.
The salt dispenser is located in the lower part of the
dishwasher (see Description) and should be filled:
*
• When the green float
cannot be seen by simply looking at
the cap of the salt dispenser.
*
• When the LOW SALT
indicator light on the control panel is
illuminated;
1. Remove the lower rack and
unscrew the container cap
(anticlockwise).
2. The first time you do this: fill the
water tank right up to its edge.
3. Position the funnel
and fill the salt container right up to its
edge (this should hold approximately
1 kg); it is not unusual for a little water to leak out.
*
4. Remove the funnel
and wipe any salt residue away from
the opening; rinse the cap under running water and then
screw it on, the head facing downwards so as to let the water
flow out of the four cracks which are arranged in a star shape
on the lower part of the cap. (Salt cap with green float
It is advisable to perform this procedure every time you
add salt to the container.
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash cycle (this could
damage the water softener beyond repair).
When necessary, measure out the salt before a wash
cycle so that any saline solution which has leaked out of the
salt dispenser is removed.
*
Only available in selected models.
*
see Water hardness
*
leves.
mmol/l
level
2
1
3
2
6
3
9
*
4
*
(see figure)
*
)
Capítulos
