FITFIU FITNESS GYM-200 Manual Del Usuario página 48

Nº Description Qua.
13 Pectoralis left arm 1
14 Stabilisation 1
15 Low bar 1
16 Low bar 1
17 Locking bar 1
18 Cross roller frame 1
19 Double pulley 1
20 Chest pulley frame 2
21 Axle 1
22 Foam roller Tube 2
23 Front base 1
24 Rear base 1
25 Arch plate 3
26 Plastic bearing 4
27 Pulley 2
28 Backrest cushion 1
29 Seat cushion 1
30 Top cable 1
31 Pec cable 1
32 Abdominal cable 1
33 Leg Cable 1
34 Abdominal Belt 1
35 Ankle strap 1
36 Upper weight plate 1
37 Weight stack 1
38 Weight bush 1
39 Weight screw 1
40 Weight washer 1
41 Weight selection bar 1
42 L-bolt 1
43 Weight buffer Ø62*16 2
44 Hexagon nut M12 6
45 Comfort handle Ø28 4
Nº Description Qua.
58 End cap with hole
59 Sleeve
60 Pulley 17
61 Pulley bush
62 Pin with ring
63 Locking link
64 Coil chain
65 Ø19 Steel bearing
66 Ø30*7 Buffer
67 M8 nylon nut
68 M10 Nylon nut 34
69 M12 Nylon nut
70 M12*115 Hexagon bolt
71 Ø6 Washer
72 Ø8 Washer
73 Ø10 Washer 50
74 Ø12 Washer
75 M12*85 Hexagon bolt
76 Ø8 Curved washer
77 Ø10 Bow washer 23
78 M10*20 hex bolt
79 M6*20 hex bolt
80 M8*20 Hexagon head bolt
81 M8*45 Hexagon head bolt
82 M8*80 Hexagon head screw
83 M10*25 Hexagon bolt
84 Hexagon head screw M10*45 15
85 M10*65 hexagon head screw
86 M10*80 hexagon head screw 13
87 Hexagon head screw M5*6
88 Cover guide
89 Top cover bracket
90 Weight stack cover
94
ASSEMBLY
2
1
GENERAL ASSEMBLY INFORMATION
4
• Assembly should be carried out by two people if possible. Read the manual carefully and look at the explanatory
1
drawing on the previous page before you start assembling.
6
• Remove all packing material and spread out all parts on a flat surface to get an overview and to facilitate assembly.
Protect the floor of the installation area with any covering.
2
• Check that all parts listed in the parts list are included. Do not dispose of the packaging material until assembly
2
is complete.
2
• Note: There is a risk of injury when using tools. Be careful and keep the working environment as risk-free as
possible. Dispose of foils or plastic bags that pose a choking hazard to children.
1
ASSEMBLY STEPS
4
2
NOTE: The instructions may contain fasteners that are pre-assembled on some parts. It may be
4
necessary to remove the fasteners to carry out the assembly, always use the original fasteners.
2
STEP 1
6
1. Attach the rear stabiliser (03) to the seat support tube (04) and secure it with 2 bolts (27), 2 washers
(34) and 2 nuts (39).
1
2. Attach the standpipe (02) to the base frame (01) and secure it with 2 bolts (30), 4 washers (35) and 2
2
nuts (39).
3. Attach the seat support tube (04) to the main support tube (02) and secure it with 2 bolts (30), 4
washers (35) and 2 nuts (39).
2
4. Secure the main support tube (05) to the seat support tube (04) with 2 bolts (30), 4 washers (35) and
4
2 nuts (39).
2
5. Attach part (#4) to part (#1) using (1) M12 nylon lock nut (#69). Tighten the nut until it is flush with the
bolt shaft.
1
2
5
2
8
4
1
2
GYM-200
95
EN